AQS-EST1-F
How to Set Your Transmitter Configuration
Frequency Band
“C
onfig S
elec
t” P
reset
Preset
U1
L1
L2
S1
S2
S3
C1
C2
C3
1
340 MHz
1435 MHz
1700 MHz
2200 MHz
2400 MHz
2200 MHz
4400 MHz
4900 MHz
4400 MHz
2
344 MHz
1442 MHz
1711 MHz
2214 MHz
2407 MHz
2221 MHz
4436 MHz
4907 MHz
4443 MHz
3
349 MHz
1449 MHz
1721 MHz
2228 MHz
2414 MHz
2243 MHz
4471 MHz
4914 MHz
4486 MHz
4
353 MHz
1456 MHz
1732 MHz
2243 MHz
2421 MHz
2264 MHz
4507 MHz
4921 MHz
4528 MHz
5
357 MHz
1464 MHz
1743 MHz
2257 MHz
2428 MHz
2285 MHz
4543 MHz
4928 MHz
4571 MHz
6
361 MHz
1471 MHz
1754 MHz
2271 MHz
2435 MHz
2307 MHz
4579 MHz
4935 MHz
4614 MHz
7
366 MHz
1478 MHz
1764 MHz
2285 MHz
2442 MHz
2328 MHz
4614 MHz
4942 MHz
4657 MHz
8
370 MHz
1485 MHz
1775 MHz
2300 MHz
2450 MHz
2350 MHz
4650 MHz
4950 MHz
4700 MHz
9
374 MHz
1492 MHz
1786 MHz
2314 MHz
2457 MHz
2371 MHz
4686 MHz
4957 MHz
4742 MHz
A
379 MHz
1499 MHz
1796 MHz
2328 MHz
2464 MHz
2392 MHz
4721 MHz
4964 MHz
4785 MHz
B
383 MHz
1506 MHz
1807 MHz
2342 MHz
2471 MHz
2414 MHz
4757 MHz
4971 MHz
4828 MHz
C
387 MHz
1514 MHz
1818 MHz
2356 MHz
2478 MHz
2435 MHz
4793 MHz
4978 MHz
4871 MHz
D
391 MHz
1521 MHz
1829 MHz
2371 MHz
2485 MHz
2456 MHz
4829 MHz
4985 MHz
4913 MHz
E
396 MHz
1528 MHz
1839 MHz
2385 MHz
2492 MHz
2478 MHz
4864 MHz
4992 MHz
4956 MHz
F
399.9 MHz
1535 MHz
1850 MHz
2399 MHz
2499 MHz
2499 MHz
4900 MHz
4999 MHz
4999 MHz
FREQUENCY MULTIPLIER
100MHz 10MHz 1MHz
Your Frequency
4
4
1 3
This digit is always
constant for a given band
and is not adjustable
Transmitter/Receiver
rotary switches
for frequency selection
MHz
Diagram A - For 1 MHz Step - L-Band, S-Band, and C-Band
FREQUENCY MULTIPLIER
10MHz 1MHz 0.1MHz
Your Frequency
7
3
2 .1
This digit is always
constant for a given band
and is not adjustable
Transmitter/Receiver
rotary switches
for frequency selection
MHz
Diagram B - For 100 KHz Step - UHF
The EST1 Transmitter has three modes for configuring the unit: Local Mode, Preset Mode, and
Remote Mode (see manual for details). Local Mode utilizes DIP switches for configuring equipped
options and rotary switches for frequency selection as shown below:
Pre-set Mode, selected when the two 10-position (BCD, 0-9) switches are set to zero and the 16-position
(binary, 0-F) is set to any position 1-F, allows local selection among 15 pre-set configurations. The EST1
transmitter ships from the factory with the 15 pre-sets configured with all options “ON” and set to their
max settings with the frequencies set per the table below. Pre-sets may be changed as outlined in the
ICD (Interface Control Document) via the communications port. Pre-sets are reprogrammable using
Remote Mode, selected when all three rotary switches are set to zero. “Remote Only” EST1 transmitters
have no rotary switches installed. See the product manual for more details.
Wiring Your EST1 Transmitter
(Audio Connections are Dependent on Configuration )
SSMA Female
Video Input
(Connect to Camera)
SMA Female
RF Output
(Connect to Antenna)
MDM-9P
Power & Programming
1:
2:
3:
4:
5:
6:
7:
8:
9:
+11 to 16 VDC Input
Ground
Ground
Ground
12 VDC Out
NC/TX Comm-
TX Comm+
RX Comm+
NC/RX Comm-
MDM-9S
Audio Input
1:
2:
3:
4:
5:
6:
7:
8:
9:
Audio 1 Mic
Audio 1 Line
Ground
Audio 2 Mic
Audio 2 Line
Ground
NC
NC
Ground
1
5
6
9
1
5
6
9
NC = No Connection
