AMP Research Power Step 77137-01A Installation Manual Download Page 13

Automatic power deploy: 

The running boards will extend down and out when the doors are opened.

Automatic power stow: 

The running boards will return to the stowed position when the doors are closed. There will be a 2-second 

delay before the running boards move to the stowed position.

Automatic stop:

If an object is in the way of the moving running board, the running board will automatically stop.

To reset, clear any obstruction, then simply open and close the door to resume normal operation.

Manually set in the deployed (OUT) position for access to the roof:

your foot while at the same time closing the door. To resume normal operation, open and close the door.

Maintenance:

 In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running 

board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to 

Avoid spraying the motors directly. After washing, apply silicone spray lubricant to the hinge pivot pins. 

Do not apply silicone, wax or protectants like Armor All® to the running board stepping surface.

Caution! 

Keep hands away when the running board is in motion.

Congratulations on your purchase of the 

genuine AMP Research PowerStep!

Here’s what you should know...

AMP  RESEARCH  warrants  this  product  to  be  free  from  defects  in  material  and  workmanship  for  FIVE  (5) YEARS  FROM 

DATE OF PURCHASE, provided there has been normal use and proper maintenance. This warranty applies to the original 

purchaser only.  All remedies under this warranty are limited to the repair replacement of the product itself, or the repair 

or replacement of any component part thereof, found by the factory to be defective within the time period specified.  The 

decision to repair or replace is wholly within the discretion of the manufacturer.

for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon 

completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage 

to our products caused by accidents, fire, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts 

not manufactured by us, is not covered under this warranty. 

ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE 

LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY.  OUR COMPANY SHALL 

NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental 

or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific 

legal rights, and you may also have other rights that vary from state to state.

FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH CUSTOMER SERVICE 1-888-983-2204

5-YEAR LIMITED WARRANTY

WARNING

Be sure to read and precisely follow the provided instructions when installing this product. Failure to do so could place the vehicle 

occupants in a potentially dangerous situation. After installing or reinstalling, re-check to insure that the product is properly installed.

AMP Research PowerStep running boards automatically move 

when the doors are opened to assist entering and exiting the vehicle.

Summary of Contents for Power Step 77137-01A














Reviews: