background image

To remove the battery pack, unscrew the top part 
of ACCU THERMO battery with bare hands. After  
unscrewing  the  top  part  of  ACCU  THERMO,  
 remove the battery pack.

Before reinstalling the battery pack and screwing on ACCU THERMO, 
check the condition of the o-ring and lubricate it with silicone grease.

PRECAUTIONS – LI-ION BATTERY PACKS
 

The battery should not be left unattended while being charged.
The battery pack must be fully charged before its first use.
Deep discharge of the pack i.e. one below 8.0 V (15% on the 
battery charger display) should be avoided.
The batteries discharge spontaneously even when they are not 
used. This may result in deep discharge and, consequently, loss 
of capacity or deterioration of the battery pack.
Before use in water, condition of the electric cables, particularly 
the E/O cable, and the charging port plug should be checked. 
If any damage is detected, the battery pack should not be used. 
The battery should be checked for leak tightness – the charging 
port plug must be appropriately tightened up.
The company Ammonite System will not be held responsible for 
any damage resulting from the misuse of ACCU THERMO.

CHARGING THE LI-ION BATTERY

To  charge  the  battery,  you  must  connect  the  charger  to  a 
100–240 V ~ power source. 
Proper  performance  of  the  charger  is  indicated  on  the  blue 
backlit display. 
Undo charging port plug on the ACCU THERMO terminal labelled 
„charging/torch”. 
The  output  plug  of  the  charger  must  be  connected  to  the  
battery’s „charging/torch” terminal.

The charge start is indicated by the display changing its colour 
from blue to red and displaying information on the battery pack 
charge status.
When the battery has been charged, the display will read „FULL 
100%”.

When the battery is charged and charger unplugged 
the  charging  port  plug  must  be  appropriately  
tightened up.

USE OF THE LI-ION BATTERY:

The  battery  must  be  charged  only  with  the  AMMO  LITHIUM 
CHARGER supplied by Ammonite System.
The battery must not be discharged below the voltage level of 
8.0 V (15% on the battery charger display).

PERFORMING THE FOLLOWING IS 
PROHIBITED:

 

Open/cut the protective wrap of the battery pack.

 

Interfere with the battery construction.

 

Short the battery contact pins.

 

Use ACCU THERMO with other batteries than genuine  

 

Ammonite System battery packs.

 

Throw the battery or pierce the cells’ casing 

 

Put the battery into fire.

 

Immerse the battery pack into the water.

STORAGE CONDITIONS OF LI-ION BATTERIES

The  battery  should  be  stored  in  a  dry,  ventilated  room  in  
ambient temperatures from +10 °C to +40 °C.

Temperatures higher than +60 °C may cause damage to the 
internal parts of the battery.

Summary of Contents for ACCU THERMO 14









Reviews: