Amit IOG761-0P001 User Manual Download Page 37

Industry Cellular Gateway

 

 

 

 

Manually:

  This gateway won’t start to establish 

WAN connection until you press “Connect” 

button on web UI. After normal data transferring 

between LAN and WAN sides, this gateway will 

disconnect WAN connection if idle time reaches 

value of Maximum Idle Time. 

 

 

Please be noted, if the WAN interface serves as the primary one for another WAN interface in Failover role, 

the Connection Control parameter will not be available to you to configure as the system must set it to “Auto-

reconnect (Always on)”. 

 

 

Network Monitoring 

It is necessary to monitor connection status continuous. 

To do it, "ICMP Check" and "FQDN Query" are used to 

check. When there is trafiic of connection, checking 

packet will waste bandwidth. Response time of replied 

packets may  also  increase.  To avoid "Network 

Monitoring"  work abnormally, enabling  "Checking 

Loading" option will stop connection check when there is 

traffic. It will wait for another "Check Interval" and then 

check loading again. 

When you do “Network Monitoring”, if reply time longer 

than "Latency" or even no response longer than 

"Checking Timeout", "Fail" count will be increased. If it is 

continuous and "Fail" count is more than "Fail Threshold", 

gateway will do exception handing process and re-initial 

this connection again . Otherwise, network monitoring 

process will be start again. 

 

 

37 

 

Summary of Contents for IOG761-0P001










































































































































































































































































































































































































Reviews: