AMI IMBM-Q87A Manual Download Page 43

Page: 43 / 48

3-13

Chapter 3: BIOS setup

3.5

Boot menu

The Boot menu items allow you to change the system boot options.

3.5.1

Boot Configuration

Quiet Boot [Enabled]

This item enables/disables Quiet Boot. Configuration options: [Disabled] [Enabled]

Launch I217LM PXE OpROM [Disabled]

This item enables/disables Legacy Boot Option for I217LM.

Configuration options: [Disabled] [Enabled]

Launch WGI210AT PXE OpROM [Disabled]

This item enables/disables Legacy Boot Option for WGI210AT.

Configuration options: [Disabled] [Enabled]

3.5.2

Boot Option Priorities

These items specify the boot device priority sequence from the available devices.

The number of device items that appears on the screen depends on the number of

devices installed in the system.

• To select the boot device during system startup, press <F7> during POST.

• To access Windows OS in Safe Mode, do any of the following:

Press <F5> during POST.

Press <F8> after POST.

Summary of Contents for IMBM-Q87A

















































Search results

Summary of Contents for IMBM-Q87A

Reviews:

Related manuals for IMBM-Q87A

Brands by name

Popular brands

AMI IMBM-Q87A, Manual

Search results

Summary of Contents for IMBM-Q87A

Reviews:

Related manuals for IMBM-Q87A

Brands by name

Popular brands