manualshive.com logo in svg

AMI Marine QUARK-ELEC NMEA 0183, Manual

Share
Download
AMI Marine QUARK-ELEC NMEA 0183 Manual Download Page 4

Quark-elec Manual 

4  of  20 

2022 

 V4.32 

6. To connect a mobile device wirelessly to the A032 through a router (Station mode)

 see

Wireless Connections chapter. 

7. Optional: Configuring 

your device’s Baud rates or WiFi settings

The A032 has been pre-set to frequently used WiFi and Baud rate settings for your convenience. If
you wish to change these settings, please use the Configuration tool. For more details, please See
the configuration section of the manual and the configuration instructions on the CD provided.

Default Baud Rate settings: 

The default NMEA 0183 input baud rate is 4800bps, the default output

baud rate is 38400bps.

Default WiFi settings:

 The A032 is pre-set to connect wirelessly to mobile devices in Ad-hoc mode

(

‘peer-to-peer’ without a router or access point). This can be changed to Station mode (connecting to

other devices through a router), using the Configuration software. WiFi can be disabled by setting
device’s WiFi to Standby mode.

Figure 1: Example setup 

Summary of Contents for QUARK-ELEC NMEA 0183





















Reviews:

No comments

Brands by name

Popular brands

Load more brands