AMG AMG5904A966B9 Instruction Manual Download Page 4

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.

Page 4 of 12

AMG5904A966B9 Instruction Sheet
D22153-00.doc

Connections

Optical Connection Singlemode

Optical Fibre ........................................Singlemode
Connector ............................................SC/PC

Primary Optical Launch Power ............-10dBm
Transmit Wavelength...........................1550nm

Primary Optical Sensitivity...................-30dBm
Receive Wavelength............................1310nm

Minimum Optical Dynamic Range .......20dB.

Power Connection

Connector Type ...................................Removable 2-pin, 3.81mm, Screw Terminal
Connector Partno.................................Phoenix 1803578
Supply Voltage.....................................+12 to +15 Volts DC
Maximum Power ..................................10 Watts

Data and Alarm Channel Connections

No. of Data Channels ..........................2
No. of Alarms .......................................8

Connectors ..........................................Removable 5-pin, 3.5mm, Spring Terminal
Connector Partnos...............................Phoenix 1952296

Data Interfaces ....................................RS-232 / 422 / 485. Selected by external slide switches D1-D2

RS-232 – Switch Position - Top
RS-422 – Switch Position - Middle
RS-485 – Switch Position - Bottom

Internal 120Ω termination resistors may be applied to RS-422 or RS-485 inputs as required by internal 

DIL switches inside the enclosure. *See appropriate section on how to remove the case for access to
the DIL switches.

Alarm inputs.........................................Input is via a series 10k resister with 47kΩ pull-up to +3V3. 

Alarm outputs.......................................Output is NPN open collector, maximum load 500mA @ 24Vdc
.

Audio Connections

Audio Channels – BANK A ..................6 Audio channels 1-6
Audio Channels – BANK B ..................8 Audio channels 1-8

Connectors ..........................................37-way D-Type female connector - shielded.
Connections.........................................See appropriate section for connections and configuration

Audio Specifications

Input level ............................................-40dBm to 0dBm
Input overload level..............................+6dBm

Input impedance ..................................56kΩ / 600Ω. Each channel individually selected using DIL 

switch on front panel

Output impedance ...............................600Ω 

Frequency response ...........................10Hz to 20KHz

Summary of Contents for AMG5904A966B9













Reviews: