AMG AMG5713A9-DIN Instruction Manual Download Page 10

AMG Systems Ltd. reserves the right to make changes to this 
document without notice. The information herein is believed to 
be accurate. No responsibility is assumed by AMG for its use.  

Page 10 of 12 

AMG5714A9-DIN Instruction Sheet 
D17378-00.doc 
 

 

 

Physical Information 

Dimensions 

Height................................................... 112mm 
Width .................................................... 170mm (excluding connectors) 
Depth ................................................... 35mm 
Weight .................................................. 600grams 
 

 

Mounting Details 

The AMG unit is supplied with a clip-on mounting bracket which is able to mount onto a DIN rail. The 
unit is clipped into the mounting bracket, and is then held firmly in position. 
 

 

Safety 

AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000. 
 
It is always advisable to follow good practice when working with optical fibre systems. This includes: 
 

 

Do not stare with unprotected eyes or with any unapproved collimating device at fibre 

ends or connector faces, or point them at other people. 

 

Use only approved filtered or attenuating viewing aids 

 
For other safety issues and advice on good practice associated with optical fibre systems, please see 
EN 60825-2:2000 or your local safety officer. 
 
 

 

Maintenance and Repair 

There are no user serviceable parts within AMG products. See unit data sheet for full specification. 
 
In case of problem or failure, please call your local support centre or contact:  

AMG Systems Ltd.

 at  

3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK. 
 
 

Phone    

 

+44 (0) 1767 600 777 

 

Technical Support  

+44 (0) 1767 604 491  

 

Email    

 

[email protected] 

 

Summary of Contents for AMG5713A9-DIN













Reviews: