AMG AMG5514R Instruction Manual Download Page 4

AMG Systems Ltd. reserves the right to make changes to this 
document without notice. The information herein is believed to 
be accurate. No responsibility is assumed by AMG for its use.  

Page 4 of 8 

AMG5514R Instruction Sheet D17366-
00.doc 
 

 

 

Connections 

Optical Connections Singlemode 

No. of Optical Connections .................. 1 
Optical Fibre ........................................ Singlemode   
Connector ............................................ SC/PC 
 
Primary Optical Launch Power ............ -10dBm 
Transmit Wavelength ........................... 1310nm 
 
Primary Optical Sensitivity ................... -30dBm 
Receive Wavelength ............................ 1550nm 
 
Minimum Optical Dynamic Range ....... 20dB. 
 

 

Power Connection 

Power supply ....................................... From plug in connection on the AMG2009 or AMG2015 subrack 
Power consumption ............................. 3.0 Watts max. 
 

 

Data and Alarm Channel Connections 

No. of Data Channels .......................... 1  
No. of  Alarms ...................................... 1  
 
Connectors .......................................... Removable 8-pin, 2.5mm, Spring Terminal 
Connector Partno. ................................ Phoenix  1881383 
 
Data Interfaces .................................... RS-232, RS-422 or R-S485. Selected by slide switch inside 

enclosure. *See appropriate section on how to remove the case 
for access to the data switches 
 

 

RS-485 – Switch Position - Top  

 

RS-422 – Switch Position - Middle 

 

RS-232 – Switch Position - Bottom 

 
Alarm input ........................................... Contact  Closure pull-up is 330R to +3V3 
Alarm Output ........................................ Solid-state  Relay, maximum 150mA at 125Vac/dc, Ron < 6.5

 

 

 

Summary of Contents for AMG5514R









Reviews: