AMG AMG4714Bx-SF Instruction Manual Download Page 4

AMG Systems Ltd. reserves the right to make changes to this 
document without notice. The information herein is believed to 
be accurate. No responsibility is assumed by AMG for its use.  

Page 4 of 12 

AMG4714Bx-SF Instruction Sheet 
D32036-00.doc 
 

 

 

Connections 

Video Output Connections 

No. of channels .................................... 1 
Connectors .......................................... 75 ohm BNC Socket. 
Output Impedance ............................... 75 ohm terminated. 
Output Level ........................................ 1 Volt p-p nominal 
Frequency Response ........................... 10Hz to 7MHz. 
 

 

Optical Connections 

PRIMARY OPTO IN

 

Connector ............................................ LC/PC 
Optical Fibre ........................................ One fibre - Singlemode  
 
Primary Optical Launch Power ............ -5dBm 
Wavelength .......................................... 1310nm 
 
Primary Optical Sensitivity ................... -22dBm 
Wavelength .......................................... 1550nm 
 

 

Power Connection 

Connector Type ................................... 2.1mm screw lock long power jack 

– centre positive  

Connector Partno. ................................ Switchcraft S761K, AMG G16125-00 
Supply Voltage ..................................... 13.5 to 18.0 Volts DC.  
Maximum Power  ................................. 10 Watts 
 

 

Data and Audio Channel Connections 

Total No. of Data Channels ................. 2 channels 
 

DATA CHANNEL A

 

Data Channel A ................................... 1 channel 
Data Connector .................................... RJ45 
 
Channel A Interface 

On Board Data Interface 

– RS232, RS422 or RS485. Selected by slide switch 

above the RJ45 connector. 
 
 

RS485 

– switch position - high (closest to BNC connections) 

 

RS422 

– switch position – middle 

 

RS232 

– switch position – low (furthest from BNC connections) 

 

DATA CHANNEL B

 

Data Channel B ................................... 1 channel 
Data Connector .................................... RJ45 
Channel B Interface ............................. Defined by data/audio interface daughter board fitted into Slot 1 

on main board and indicated by the 'x'  in the AMG partno. 

 

Summary of Contents for AMG4714Bx-SF













Reviews: