manualshive.com logo in svg

America's Heat AHB-170P, Owner'S Manual

Share
Download
America's Heat AHB-170P Owner'S Manual Download Page 6

 
 

5 

 

Unpacking and Setup 

 

After removal of shipping container, position storage bin on storage bin base at desired angle for 
installation. 
 
Install auger assembly by sliding auger boot (with clamp) over bin outlet; align elbow on bin auger 
tube directly over boiler fuel inlet.  Tighten auger boot clamp securely.  It is advisable to install two 
sheet metal screws (not supplied) thru the clamp, auger boot, and into the hopper bin outlet to insure a 
permanent connection.  Install fuel delivery coupler between bin auger tube and boiler fuel inlet.  (See 
Figure 1) 
 
Fasten flex conduit extending from storage bin auger assembly to boiler auger motor housing using 
conduit lock nut.  (See Figure 1) 
 
Connect one black auger motor lead to the two orange wires with wire nut connector.  Connect the 
other black auger motor lead to the two white wires using wire nut connector.  (See Figure 1) 

 

 
 
 

 
 
 
 
 
 
 
 
 
 
 

 
 
 

FIGURE 1 

 

 
 
 
 

 

 
 
 
 

 

Figure 1: Unpacking and Setup 

 

Summary of Contents for AHB-170P


























Reviews:

No comments

Brands by name

Popular brands

Load more brands