American Water Heater 40-42K Installation Instructions Manual Download Page 4

4

Location Requirements

FIRE AND EXPLOSION HAZARD

Can result in serious injury or death

        Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance. 
Storage of or use of gasoline or other 
flammable vapors or liquids in the vicinity 
of this or any other appliance can result in 
serious injury or death.

Flammable Vapors

FLAMMABLES

Read and follow water heater warnings and 
instructions.

WARNING

Do not use or store flammable products such as gasoline, 
solvents, or adhesives in the same room or area near the 
water heater. If such flammables must be used, all gas 
burning appliances in the vicinity must be shut off and their 
pilot lights extinguished. Open the doors and windows for 
ventilation while flammable substances are in use. 
If flammable liquids or vapors have spilled or leaked in 
the area of the water heater, leave the area immediately 
and call the fire department from a neighbor’s home. Do 
not attempt to clean the spill until all ignition sources have 
been extinguished.

WARNING

 

Fire or Explosion Hazard

Read instruction manual before installing, 

using or servicing water heater.

Improper use may result in fire or explosion.

Maintain required clearances to combustibles.

Keep combustibles such as boxes, magazines, clothes, 
etc. away from the water heater area. 

Site Location

• 

Select a location near the center of the water piping  
system. The water heater must be installed indoors  
and in a vertical position on a level surface. 

• 

Consider the inlet and exhaust vent system piping  and 
combustion air supply requirements when selecting 
the water heater location. The venting system must 
be able to run from the water heater to the termina-
tion with a minimal length and number of elbows. The 
venting system must comply with the requirements set 
forth in the venting section of this manual.  

• 

Locate the water heater near the existing gas 
piping. If installing a new gas line, locate the water  
heater to minimize the pipe length and elbows. 

NOTE:  This water heater must be installed according to all 
local and state codes or, in the absence of local and state 
codes, the “National Fuel Gas Code”, ANSI Z223.1(NFPA 
54)-current edition. 

Carbon Monoxide Poisoning Hazard

Do not install in a mobile home.
Doing so can result in death or 
carbon monoxide poisoning.

WARNING

Summary of Contents for 40-42K

























Reviews: