background image

M 9 6 8 5 8 1   R e v . 1 . 1

R E D

S T R I P E

B L U E

S T R I P E

2

MAKE WATER SUPPLY CONNECTIONS

Turn off hot and cold water supplies before beginning.

Connect FLEXIBLE SUPPLIES 

(1, 2)

 directly to wall supplies. Connection

on fitting supplies are 3/8" compression. Connect left supply
(Marked with a Red Stripe) to Hot and right supply (Marked with
Blue Stripe) to Cold wall supply. Use adjustable wrench to 
tighten connections. Do not over tighten.

Faucet supplies are 27-1/2" long from faucet base.

Note: If additional supply length
is required, installer must
purchase additional parts
separately.

Important: If SUPPLY HOSES
(1, 2) are too long, loop as 
illustrated to avoid kinking.

1

2

COLD

HOT

3

CONNECT HOSE SPRAY
and INSTALL WEIGHT

Figure 2

Check that seal washers are installed in both ends of SPRAY HOSE ADAPTER 

(1).

Thread SPRAY HOSE ADAPTER 

(1)

 onto faucet SHANK 

(2)

. Tighten with adjustable wrench.

Figure 1.

Thread HOSE END 

(3) 

into bottom of SPRAY HOSE ADAPTER 

(1). 

Tighten with adjustable wrench.

Make sure all connections are tight. 

Figure 1. 

 

Install RUBBER BUSHING 

(4)

 onto SPRAY HOSE 

(5)

. Install WEIGHTS 

(6)

 onto HOSE 

(5) 

using two screws 

(7)

. Locate

WEIGHTS 

(6)

 18" from underside of mounting surface on HOSE 

(5)

. Tighten SCREWS 

(5)

 firmly. 

Figure 2.

SEAL

WASHER

SEAL

WASHER

2

1

3

5

7

6

4

Figure 1

UNDER SIDE

OF MOUNTING

SURFACE

18"

Summary of Contents for Pekoe Pull-Down 4332.300.XXX

Page 1: ...le RUBBER WASHER 5 PLASTIC WASHER 6 RUBBER METAL C WASHERS 7 and long LOCKNUT 8 onto SHANK 3 from underside of sink Hand tighten LOCKNUT 8 and check that faucet is centered Tighten LOCKNUT 8 with WRENCH 12 supplied Insert screwdriver into hole in WRENCH 12 and tighten Feed HOSE END 9 through HOSE GUIDE 10 Slide other side of HOSE GUIDE 10 onto SHANK 3 and secure with LOCK NUT 11 Do not over tighte...

Page 2: ...ditional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking 1 2 COLD HOT 3 CONNECT HOSE SPRAY and INSTALL WEIGHT Figure 2 Check that seal washers are installed in both ends of SPRAY HOSE ADAPTER 1 Thread SPRAY HOSE ADAPTER 1 onto faucet SHANK 2 Tighten with adjustable wrench Figure 1 Thread HOSE END 3 into bottom of SPRAY HOSE ADAPTER 1 Tighten with ad...

Page 3: ...ble CARTRIDGE 6 Replace CARTRIDGE NUT 5 CAP 4 and HANDLE assembly check flow SERVICE Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then 5 6 HOT COLD SUPPLIES CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A C...

Page 4: ...a Inc 2008 IN MEXICO 01 800 839 12 00 M962690 0070A CARTRIDGE NUT M9629691 YYY0A CARTRIDGE COVER M962689 0070A CARTRIDGE M962688 YYY0A HANDLE KIT M962659 0070A MOUNTING KIT M962660 0070A HOSE GUIDE M962650 0070A HOSE WEIGHTS M962661 0070A NUT M962662 0070A SPRAY HOSE ADAPTER WITH CHECK VALVE M962686 0070A O RING M962685 YYY0A PEDESTAL M962683 YYY0A PULL OUT SPRAY WITH CHECK VALVE M962652 0070A SPO...

Reviews: