A
B
Single Bowl
Double Bowl
Trap
Trap
Perimeter
of sink
Cutout
Perimeter
of sink
Cutout
1
2
3
5
4
6
8
7
Drill a clearance hole
inside the cutout line
as marked on the
countertop.
Connect supply lines to
faucet finger tight, and
carefully bend to engage
with the supply stops.
Tighten connections to
faucet for secure seal.
Remove sink and apply
a masking tape outline
1/8" outside traced
outline as a guide for
application of silicone
sealant.
Connect drain assembly
hand tight to check align-
ment. It may be necessary
to cut off part of the tailpiece
(area "A") or part of the
horizontal leg of the trap
(area "B").
Secure joint for watertight
assembly.
AFTER THE CUTOUT IS DRAWN...
© A M E R I C A N S T A N D A R D I N C . 2 0 0 4
7 9 0 7 1 5 - 1 0 0 R e v . S
AMERICAST
®
LIMITED LIFETIME WARRANTY
If an American-Standard Americast® brand product is found to be defective in
materials or workmanship, after inspection by an authorized American-Standard
representative, American-Standard will repair or, at its option, exchange the product for a
similar model. This warranty extends for the lifetime of the product, so long as it remains
in use in its original place of installation, except that the warranty applies to a bathing
vessel’s slip-resisting surface only for the first year after the product’s initial installation.
This warranty applies only to the original purchaser and installation of these products.
This warranty does not apply to whirlpool components or to faucets, drains,
mounting rims, grab bars or other accessories. If manufactured or supplied by American-
Standard, such whirlpool components and accessories are covered under separate
limited warranties.
This warranty does not apply to local building code compliance. Since local building
codes vary considerably, the purchaser of this product should check with a local building
or plumbing contractor to assure local code compliance before installation.
This warranty shall be void if the Americast® brand product has been moved from
its initial place of installation; if it has been subjected to faulty maintenance, abuse,
misuse, accident or other damage; if it was not installed in accordance with American-
Standard’s instructions; or if it was modified in a manner inconsistent with the product as
shipped by American-Standard.
American-Standard's option to repair or exchange the product under this warranty
does not cover any labor or other costs of removal or installation, nor shall American-
Standard be responsible for any other incidental or consequential damages
attributable to a product defect or to the repair or exchange of a defective product,
all of which are expressly excluded from this warranty. (Some states or provinces do
not allow the exclusion or limitation of implied warranties, so this exclusion may not apply
to you.)
This warranty gives you specific legal rights. You may have other statutory rights that
vary from state to state or from province to province, in which case this warranty does
not affect such statutory rights.
For service under these warranties, it is suggested that a claim be made through the
contractor or dealer from or through whom the product was purchased, or that a service
request (including a description of the product model and of the defect) be sent to the
following address:
Product names listed herein are trademarks of American Standard Inc.unless otherwise noted.
CARE AND CLEANING...
For all porcelain enamel surfaces, regular, gentle care is best. The
recommended way to preserve the finish, avoid scratches, and clean
porcelain enamel fixtures is to rinse them with detergent and water.
Generally, any of the light duty liquid dishwashing detergents, such
as Palmolive or Dawn, work well. In areas where the water is hard,
a heavy duty liquid laundry detergent such as liquid Tide will work better.
Palmolive® is a registered trademark of Colgate-Palmolive Co.
Tide® and Dawn® are registered trademarks of Procter and Gamble.
2
1/8"
Sink
Masking
Tape
Masking
tape
outline
Sink
outline
Cutout
Silicone
Sealant
Apply a generous portion of silicone sealant inside line
traced on countertop. Carefully lower sink into place
and press down firmly. Use guidelines for proper
positioning. Using water to dampen your finger,
remove excess sealant for a smooth even line. Apply
additional sealant if necessary to provide a uniform
bead from the rim of sink to the masking tape line as
shown. Carefully remove tape. Dampen finger and run
it slightly over the sealant to remove any high spots.
Use mineral spirits to remove excess silicone from
countertop and sink.
NOTE: Silicone must be removed within 10 minutes
of application or a permanent residue may remain
on the surfaces.
Before applying the sealant,
place the sink temporarily
into the cutout. Check for
alignment and clearance,
then trace around the
outside edge of the sink
as a guide for installation
location and application
of sealant.
Cut opening on cut line
inside the perimeter of
sink.
Note - Formica counter-
top installation only is
illustrated. Contact your
countertop distributor for
the best method of cut-
ting other materials such
as marble, hard syn-
thetics, etc.
Mount the faucet and
drain assembly on the
sink or countertop
following the
manufacturer's
instructions.
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
www.AmericanStandard-US.com
www.AmericanStandard.ca
www.AmericanStandard.com.mx
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
Toll Free: (800) 387-0369
Ecatepec 55540 Edo. Mexico