DRAIN INSTALLATION
3
(Models 6801 and 6831 only)
Push TAILPIECE
(1)
down into TRAP
(2)
(threaded end up).
Thread LOCKNUT
(3)
, WASHER
(4)
and
GASKET
(5)
onto DRAIN BODY
(6)
.
Apply a bead of PUTTY to underside
of FLANGE
(7)
.
Feed DRAIN BODY
(6)
up through SINK
and thread FLANGE
(7)
fully onto BODY
(6)
.
Tighten LOCKNUT
(3)
firmly, keeping the
PIVOT ROD
(8)
pointed towards the back
of the SINK.
Drop STOPPER
(9)
into DRAIN BODY
(6)
.
Pull TAILPIECE
(1)
up and thread tightly
into DRAIN BODY
(6)
.
Position EXTENSION ROD
(10)
onto POP-UP
ROD
(11)
and tighten THUMBSCREW
(12)
.
Remove one end of CLIP
(13)
from PIVOT ROD
(11)
by squeezing ends together while sliding.
Insert PIVOT ROD
(14)
into second or third hole
in EXTENSION
(10)
and reassemble CLIP
(13)
.
(EXTENSION
(10)
may need to be bent.)
Adjust STOPPER
(9)
height by repositioning
EXTENSION
(10)
and tightening THUMBSCREW
(12)
.
SINK
PUTTY
TEST INSTALLED FAUCET
6
Remove AERATOR.
Turn VALVES
(1)
to off position.
Insert ADAPTOR
(8)
with larger
diameter over the VALVE STEM
(4)
.
Align LEVER
(2)
or WRIST
BLADE HANDLE
(3)
and install
onto VALVE STEM
(4)
.
Insert BLUE INDEX
(5)
into
cold valve (right side) and red
INDEX
(6)
into hot valve (left side).
Insert HANDLE SCREW
(7)
into
HANDLES and tighten with
screwdriver.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and TEE connections for leaks.
Turn handles into OFF position and replace AERATOR.
Apply a bead of PUTTY around underside
of DRAIN FLANGE
(1)
flange. Insert DRAIN
PLUG
(2)
into SINK drain hole.
Hold DRAIN PLUG
(2)
to prevent turning and
assemble GASKET
(3)
, WASHER
(4)
, and
LOCKNUT
(5)
from underneath sink.
Apply sealant to threaded end of TAILPIECE
and thread into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY (6542.140/.170)
PUTTY
SINK
SEALANT
4
INSTALL HANDLES
5
SERVICE
7
CARTRIDGE
SCREEN
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW,
and INDEX.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW
and INDEX.
SPRING
CLIP
STOP
WASHER
90°
1
3
4
5
6
4
2
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
3
5
7
6
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
AERATOR
6 018 6 Rev. 1. 4
8
