H48
© 2008 AS America Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP
OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL GRAB BAR KIT AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
●
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH
CIRCULATING SYSTEM PIPING. MOUNTING HOLES DRILLED BY INSTALLER.
SUPPLY PIPING NOT INCLUDED.
ON SYSTEM II VARIATION
: SYSTEM CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL A MINIMUM OF (152MM) 6"
ABOVE ROUGH FLOOR.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
1829mm
(72)
927mm
(36-1/2)
OUTLINE OF CUTOUT
1791 X 1181
(70-1/2 X 46-1/2)
C/L OF
DRAIN
102mm
(4)
PUMP
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
305mm
(12)
1219mm
(48)
229mm x 356mm
(9 x 14) FLOOR
CUTOUT
LEVELING STRINGER
(NOT FOR SUPPORT)
RECOMMENDED
FITTING
LOCATION
64X279mm
2-1/2 X 11)
1-1/2 N.P.T.M. THREADS
51mm
(2)
105mm
(4-1/8)
C/L OF
OVERFLOW
495mm
(19-1/2)
546mm
(21-1/2)
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
1-1/2 O.D.TAILPIECE
OPTIONAL
DECK FITTING
AREA
GRAB BAR
FITTING AREA
64mm
(2-1/2)
121mm
(4-3/4)
SAFE-T-
HEATER
REMOVABLE
BLANK
GENERAL SPECIFICATIONS FOR 2711 WHIRLPOOL
72 x 48 x 21-1/2 In. (1829 x 1219 x 546mm)
148 Lbs. (67 Kg.)
965 Lbs. (434 Kg.)
95 Gal. (360 L)
74 Gal. (280 L)
43 x 28 In. (1092 x 711mm)
68 x 38 In. (1727 x 965mm)
14-5/8 In. (371mm)
40 Lbs./Sq.Ft. (195 Kgs./Sq.m)
30.3
60.8
2.1 HP, 15.6 AMPS ,120V.
SYSTEM II PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
Revised 2/08
ELLISSE™ 6' x 48"
WHIRLPOOL AND BATHING POOL
HIGH GLOSS
1829mm
(72)
927mm
(36-1/2)
OUTLINE OF CUTOUT
1791 X 1181
(70-1/2 X 46-1/2)
C/L OF
DRAIN
102mm
(4)
305mm
(12)
1219mm
(48)
229mm x 356mm
(9 x 14) FLOOR
CUTOUT
LEVELING STRINGER
(NOT FOR SUPPORT)
RECOMMENDED
FITTING
LOCATION
64X279mm
2-1/2 X 11)
1-1/2 N.P.T.M. THREADS
51mm
(2)
105mm
(4-1/8)
C/L OF
OVERFLOW
495mm
(19-1/2)
546mm
(21-1/2)
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
1-1/2 O.D.TAILPIECE
OPTIONAL
DECK FITTING
AREA
GRAB BAR
FITTING AREA
64mm
(2-1/2)
121mm
(4-3/4)
GENERAL SPECIFICATIONS FOR 7211 BATHING POOL
72 x 48 x 21-1/2 In. (1829 x 1219 x 546mm)
133 Lbs. (60 Kg.)
950 Lbs. (432 Kg.)
95 Gal. (360 L)
43 x 28 In. (1092 x 711mm)
68 x 38 In. (1727 x 965 mm)
14-5/8 In. (371mm)
40 Lbs./Sq.Ft. (195 Kgs./Sq.m)
30.3
60.8
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)