A
B
Double Bowl
Trap
4
5
7
8
Connect supply lines to
faucet finger tight, and
carefully bend to engage
with the supply stops.
Tighten connections to
faucet for secure seal.
Before applying the
sealant, place the sink
temporarily into the
cutout. Check for
alignment and clear-
ance, then trace
around the outside
edge of the sink as
a guide for installation location and application of
sealant. Remove sink.
6
Connect drain assembly
hand tight to check
alignment. It may be
necessary to cut off part
of the tailpiece (area "A")
or part of the horizontal
leg of the trap (area "B").
Secure joint for water-
tight assembly.
7 9 1 2 6 6 - 4 0 0 R e v . B
2
Apply a masking tape
outline 1/8" outside
traced outline as a
guide for application
of silicone
sealant.
1/8"
Masking
tape
outline
Sink
outline
Cutout
Product names listed herein are trademarks of American Standard Inc.unless otherwise noted.
American Standard Inc. 2003
C
CARE AND CLEANING...
For all porcelain enamel surfaces, regular, gentle
care is best. The recommended way to preserve the
finish, avoid scratches, and clean porcelain enamel
fixtures is to rinse them with detergent and water.
Generally, any of the light duty liquid dishwashing
detergents, such as Palmolive or Dawn, work well.
In areas where the water is hard, a heavy duty liquid
laundry detergent such as liquid Tide will work better.
Palmolive® is a registered trademark of Colgate-Palmolive Co.
Tide® and Dawn® are registered trademarks of Procter and Gamble.
Sink
Masking
Tape
Silicone
Sealant
Apply a generous portion of silicone sealant inside line
traced on countertop. Carefully lower sink into place
and press down firmly. Use guidelines for proper
positioning. Using water to dampen your finger,
remove excess sealant for a smooth even line. Apply
additional sealant if necessary to provide a uniform
bead from the rim of sink to the masking tape line as
shown. Carefully remove tape. Dampen finger and run
it slightly over the sealant to remove any high spots.
Use mineral spirits to remove excess silicone from
countertop and sink.
NOTE: Silicone must be removed within 10 minutes
of application or a permanent residue may remain
on the surfaces.
Single Bowl
Trap
Perimeter
of sink
Cutout
Perimeter
of sink
Cutout
1
2
3
Drill a clearance hole
inside the cutout line
as marked on the
countertop.
Mount the faucet and
drain assembly on the
sink following the
manufacturer's
instructions.
Cut opening on cut
line inside the peri-
meter of sink.
AFTER THE CUTOUT IS DRAWN...
AMERICAST
®
LIMITED LIFETIME WARRANTY
If an American-Standard Americast® brand product is found to be defective in materials or
workmanship, after inspection by an authorized American-Standard representative, American-
Standard will repair or, at its option, exchange the product for a similar model. This warranty
extends for the lifetime of the product, so long as it remains in use in its original place of
installation, except that the warranty applies to a bathing vessel’s slip-resisting surface only for
the first year after the product’s initial installation.
This warranty applies only to the original purchaser and installation of these products.
This warranty does not apply to whirlpool components or to faucets, drains, mounting rims,
grab bars or other accessories. If manufactured or supplied by American-Standard, such
whirlpool components and accessories are covered under separate limited warranties.
This warranty does not apply to local building code compliance. Since local building codes
vary considerably, the purchaser of this product should check with a local building or plumbing
contractor to assure local code compliance before installation.
This warranty shall be void if the Americast® brand product has been moved from its initial
place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or
other damage; if it was not installed in accordance with American-Standard’s instructions; or if it
was modified in a manner inconsistent with the product as shipped by American-Standard.
American-Standard's option to repair or exchange the product under this warranty does not
cover any labor or other costs of removal or installation, nor shall American-Standard be
responsible for any other incidental or consequential damages attributable to a product
defect or to the repair or exchange of a defective product, all of which are expressly
excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation
of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from
state to state or from province to province, in which case this warranty does not affect such
statutory rights.
For service under these warranties, it is suggested that a claim be made through the
contractor or dealer from or through whom the product was purchased, or that a service request
(including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard Inc.,
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States,
warranty information may also be
obtained by calling the following
toll free number: (800) 442-1902
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
