M 9 6 8 6 4 1 R E V. 1 . 2
1
4
10
TEST INSTALLED FITTING
With HANDLE
(1)
in OFF position, turn on WATER
SUPPLIES
(2)
and check all connections for leaks.
Remove AERATOR
(3)
.
Operate HANDLE
(1)
to flush water lines thoroughly.
Replace AERATOR
(3)
.
3
CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB
(4)
and fill lavatory with water.
Check that DRAIN STOPPER
(5)
makes a good seal
and retains water in Sink. If DRAIN STOPPER
(5)
does not seal properly, please refer to Troubleshooting
section in these instructions.
Release POP-UP KNOB
(4)
down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
12
4
OFF
ON
HOT
COLD
5
“P” TRAP
WASTE
OUTLET
2
2
CARE INSTRUCTIONS:
1
2
2.5mm HEX KEY
3
8
4
A
B
D
5
6
REMOVE
INSTALL
7
10
11
SERVICE
To remove or replace cartidge:
To adjust HOT LIMIT SAFETY STOP:
Turn valve to OFF position.
Pull out PLUG BUTTON
(1)
and remove HANDLE SCREW
(2)
.
Pull off HANDLE
(3)
and CAP
(4)
.
Unthread CARTRIDGE NUT
(5)
and remove.
Pull out CARTEIDGE
(6)
.
Inspect CARTRIDGE
(6)
and O-RINGS
(7)
for debris and
clean if necessary.
Clean MANIFOLD
(8)
and rinse clean.
Reinstall CARTRIDGE
(6)
and O-RINGS
(7)
onto MANIFLOD
(8)
.
Reinstall CARTRIDGE NUT
(5)
, CAP
(4)
and HANDLE ASSEMBLY
(3)
.
If spout drips, operate handle several times from OFF to ON and
HOT to COLD position. Do not force - handle turns only 90˚.
Turn off hot and cold water
supplies before beginning.
CAUTION
By restricting HANDLE rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP
(9)
reduces risk of accidental scalding. To lower the
maximum hot water temperature of your faucet, all you need
to do is adjust the setting on the HOT LIMIT SAFETY STOP
(9)
.
Note: The HOT LIMIT SAFETY STOP (9) is set at the maximum
hot temperature setting from the factory. Fig. A.
ADJUST HOT LIMIT SAFEYT STOP
Remove HANDLE ASSEMBLY
(3)
, CAP
(4)
and CARTRIDGE NUT
(5)
.
Set the CARTRIDGE STEM
(10)
to the OFF position and rotate it
clockwise until stops.
Fig. B.
Rotate the CARTRIDGE STEM
(10)
counter-clockwise to a colder
setting mark in the HOT LIMIT SAFETY STOP
(9)
.
Fig. C.
Lift up the HOT LIMIT SAFETY STOP
(9)
and rotate it to coincide
again with the stop in the base of the CARTRIDGE STEM
(10)
.
Fig. D.
Replace the HOT LIMIT SAFETY STOP
(9)
.
Reinstall CARTRIDGE NUT
(5)
, CAP
(4)
and HANDLE ASSEMBLY
(3)
.
GEAR
GEAR
GEAR
10
9
9
C
10
9
+HOTTER
SETTING
MARKS
COLDER
GEAR
10
9
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
