background image

M968583

4101.301

HI-FLOW KITCHEN FAUCET

with SIDE SPRAY

Installation

Instructions

Certified to comply with ANSI A112.18.1M

1

INSTALL FAUCET WITH DECK ESCUTCHEON
(4101.351)

ARCH

ALIGN SLOT

AND TAB

SLOT

TAB

Assemble RUBBER WASHER 

(4)

, BRASS WASHER 

(5)

, and threaded LOCKNUT 

(6)

 onto SHANK 

(3)

 from underside

of sink or mounting surface. Hand tighten LOCKNUT 

(6)

 and check that rotation of HANDLE 

(7)

 from HOT to COLD

is centered.

Assemble RUBBER WASHER 

(4a)

, BRASS WASHER 

(5a)

, and threaded LOCKNUT 

(6a)

 onto SHANK 

(10)

 from underside

of sink or mounting surface. Hand tighten LOCKNUT 

(6a)

. Use a screwdriver to tighten SCREWS 

(8a)

 on LOCKNUT 

(6a)

the same as fitting installation above.

Use a screwdriver to tighten SCREWS 

(8)

 on LOCKNUT 

(6)

. Work your way around LOCKNUT 

(6)

, tightening  the

SCREWS 

(8)

 slightly each time until all are snug to ensure even pressure.

Install SPRAY HOLDER: 

Insert SPRAY HOLDER 

(11)

 into ESCUTCHEON 

(1). 

From underside of sink or mounting surface

thread LOCKNUT 

(12)

 onto SPRAY HOLDER 

(11)

 shank and tighten. 

 

 

Installation with DECK ESCUTCHEON: 

Apply a light bead of plumbers putty to underside of ESCUTCHEON 

(1)

 if mounting

surface is uneven.

 

Place ESCUTCHEON 

(1)

 onto sink or mounting surface with large opening to the right as shown

Insert

supply HOSES 

(2)

 and SHANK 

(3)

 through ESCUTCHEON 

(1)

 and mounting surface. 

Make sure slot in fitting base aligns

with tab on

 ESCUTCHEON 

(1). Figure 1.

Install SPOUT ASSEMBLY:

 

Insert SPRAY HOSE 

(9)

 and SHANK 

(10)

 through ESCUTCHEON 

(1)

 and mounting surface.

Make sure slot in spout base aligns with tab on ESCUTCHEON 

(1). Figure 2.

Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

RECOMMENDED

TOOLS

Adjustable Wrench

Regular Screwdriver

Phillips Screwdriver

Turn off water at

main supply.

CAUTION

1

4a

5a

9

10

6a

8a

7

4101.301

Figure 2

ALIGN SLOT 

AND TAB

SLOT

TAB

4

1

2

3

5
6
8

11

12

Figure 1

Channel Locks

4101.301 shown with

optional escutcheon 4101.000P

Summary of Contents for Arch Control Kitchen Faucet 4101.301






Reviews: