background image

M 6 6 2 3 2   R e v. 1 . 1

HANDSHOWER INSTALLATION (Mode 8971 series only)

SERVICE

TEST INSTALLED FAUCET

To change direction of handle rotation, 

proceed as follows:

Turn valve to OFF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP 

(1)

.

Lift STOP WASHER 

(2)

, turn 90

p

 and replace.

Replace SPRING CLIP 

(1)

.

Replace ADAPTER, HANDLE, SCREW, and

INSERT.

Plastic SCREEN 

(3)

in CARTRIDGE 

(4)

may accumulate

dirt causing reduced water flow. To clean, first

turn off hot and cold water supplies, then:

Remove HANDLE (see above).
Unscrew CARTRIDGE 

(3)

with wrench.

Thoroughly rinse plastic SCREEN 

(4)

at

base of CARTRIDGE 

(3)

.

Replace CARTRIDGE 

(3)

until flange is 

tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW,

and INSERT.

Check with local codes, and if required, add a vacuum breaker

kit (part no. 028708) at specified height.  Refer to the instal-

lation instructions supplied with the kit.

IMPORTANT

Drop ESCUTCHEON 

(1)

through the fourth hole of the tub ledge

(12" max from SPOUT center) with HOLDER 

(2)

directed towards

tub center. Be sure RUBBER RING 

(3)

is properly seated in

ESCUTCHEON

(1)

. Attach RUBBER WASHER 

(4)

and BRASS WASHER 

(5)

from underside of ledge. Secure ESCUTCHEON 

(1)

by tightening locknut.

Add SEAL WASHER 

(6)

and connect HOSE 

(7)

to outlet nipple on

bottom of COUPLING 

(10)

. Tighten firmly.

Unscrew HOLDER 

(2)

from ESCUTCHEON 

(1)

. Slip SHOWER HOSE 

(8)

with COUPLING NUT through HOLDER 

(2)

and ESCUTCHEON 

(1)

.

Install SEALS 

(6)

and connect both HOSES 

(7, 8)

, attach

HOLDER

(2)

to ESCUTCHEON 

(1)

and connect

HANDSHOWER

(9)

.

When not in use, HANDSHOWER should be seated 
in the HOLDER.

NOTE

To replace SHOWER HOSE, proceed as follows:

Disconnect HANDSHOWER.
Unscrew HOLDER and pull SHOWER HOSE until hose

coupling appears.
Prevent HOSE from slipping back (use clamp, tape, etc.)
Disconnect SHOWER HOSE.

Remove HOLDER from old HOSE and slip over new

SHOWER HOSE.

Insert new SEALS and connect HOSES and HANDSHOWER.
Open valves, lift transfer knob and check for leaks.

Release HOSE, screw HOLDER back to ESCUTCHEON,

and seat HANDSHOWER.

Before the bathroom is completely finished, you may 

want to remove spout, handshower, and handles.

To remove handles, see separate "Instruction Sheet."

See separate "Instruction Sheet for handle installation.

To remove SPOUT 

(1)

, proceed as follows:

Lift TRANSFER ROD 

(2)

and unscrew KNOB 

(3)

. (Model 3941 only).

Remove PLUG BUTTON 

(4)

and remove SET SCREW 

(5)

using 5mm hex wrench supplied.

Lift SPOUT 

(1)

off SHANK 

(6)

carefully

and remove RUBBER RING 

(7)

.

Unscrew SHANK SLEEVE 

(8)

and lift TRANSFFER ROD 

(2)

from  SHANK 

(6)

(Model 3901 & 3941 only).

Reverse sequence to re-install SPOUT 

(1)

. Be sure

RUBBER RING 

(7)

is properly seated in its recess at the

base of the SPOUT 

(1)

. Make certain SET SCREW 

(5)

is

properly aligned and tight so that SPOUT 

(1)

is locked in place.

The flow rate of this Tub Filler exceeds 20 gallons/minute

at higher water pressure. Do not fill bathtub unattended.

CAUTION

LOCKNUT

1

2

3
4
5

6

7

8

9

6

6

10

3

3

4

4

3

4

5

7

8

6

1

1

1

2

2

2

Turn VALVES 

(1)

 to "off" position.

Lift HAND SHOWER 

(3)

 from holder, direct spray into tub, lift

TRANSFER KNOB 

(4)

 to check HAND SHOWER 

(3)

 and HOSES for leaks.

Turn VALVES "off."

With handles in "off" position, turn on water supplies and check

all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT 

(2)

 mounting for leaks.

If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90

$

.

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 8:00 p.m. EST

IN CANADA  1-800-387-0369   (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 1999

IN MEXICO  01-800-839-12-00

Reviews: