Page 1 of 2
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
©2021 American Lighting, Inc. REV2143 www.AmericanLighting.com
S SMART
SWITCH
120V
INSTALLATION INSTRUCTIONS
SPKPL-120VSW-WH
SAFETY INFORMATION
• Read all installation instructions before beginning; if not qualified, do not attempt
installation. Contact a qualified electrician.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention
to this manual and stay within its guidelines when using this product. Save these
instructions for future use.
• This product is suitable for indoor use in dry locations only.
• Do not submerge in liquids nor use the product in the vicinity of standing water or
other liquids, or where water can accumulate.
• Do not use if there is any damage to the product; inspect periodically.
• Do not install in tanks or enclosures of any kinds.
• This product utilizes Bluetooth® 2.4Ghz wireless technology.
• The rated input power for this unit is 100-120V AC 60Hz.
• The maximum rated current for this unit is 15A.
• The standby power consumption of this unit is ≤0.5W.
• This unit is not intended to be used in conjuction with a any dimmer.
These products may represent a possible shock or fire
hazard if improperly installed or attached in any way.
Products should be installed in accordance with these
instructions, current electrical codes, and/or the current
National Electric Code (NEC).
Do not exceed maximum recommended loads! 15A total.
Electricity can cause personal injury and property
damage if handled improperly.If you are not sureabout
any part of these instructions,please seek professional
assistance from a qualified electrician.Ensure all wark
meets applicable local and national codes.
WARNING
WARNING
WARNING: RISK OF ELECTRIC SHOCK
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 5
FIGURE 4
Tools Needed:
Switch
Cover Panel
Wire Nuts
Screws
Phillips Head Screwdriver Pliers
Flat-Head Screwdriver
Voltage Tester
Single Pole
3-Way
CONTENTS:
CONSIDERATIONS:
INSTALLATION:
Disconnect power from source prior to attempting installation
.
Make all connections and mount in place prior to providing power to system. This
product is designed to be installed in a single gang junction box.
1. Locate the circuit breaker panel and turn off the power to each switch being
replaced/installed. More than one circuit breaker may need to be turned off.
See Figure 1.
2. Remove the existing faceplate by unscrewing the mounting screws and pull it
away from the wall. See Figure 2.
3. Verify power is off. Once the faceplate is removed from the existing switch,
use an electrical voltage tester to test all wires connected to the switch to ensure
there is no voltage in the circuit. See Figure 3.
4. Unscrew the mounting screws from the junction box and pull out the existing
switch. See Figure 4.
5. Identify whether the existing switch is a Single Pole Switch or a 3-Way Switch.
See Figure 5.
- Single Pole: One switch controls one light or one bundle of lights.
- 3-Way: Two switches control the same light or the same bundle of lights.
6. Idenfity the Line and Load wires. Line wires are usually BLACK, attached with a
BLACK screw, and may be marked “common”. See Figure 6.
- Note: The color of your wire may be different from the color shown in Figures.
Continued on next page...
30min
Approximately
30 minutes to install
and setup the switch
1
2
Switch Status
Remarks
Light Status
Light Color
Green
OFF
ON
Power OFF(Default)
Power ON(Default)
Blink Quickly
(0.5s )
Blink Slowly
(1s )
ON/OFF
LED Indicator
Cover Panel
Single Pole
3-Way
3-Way
FIGURE 6
Line /Hot
Load
Line /Hot
Traveler
Traveler
Single Pole
3-Way
