4 INSTALLATION
GUIDE
SENSORNET 6-POSITION JUNCTION BOX
8000-0975-01, REV. F
Specifications
Electrical
Power Source .................... 100–120/200–240Vac
1.6A/.08A, 50–60Hz
Power Consumption: ......... 250W max.
Voltage Output:.................. 28Vac, 3A per Class 2
output, 6A total.
Do not parallel outputs.
For dry location.
Fuses F1, F2:..................... 2A, 250V, Slow Blow
Fuses F3, F4:..................... 6.3A, 250V, Slow Blow
Dimensions
Height: ............................... 32cm (12.6in)
Width: ................................ 21cm (8.3in)
Depth: ................................ 16cm (6.3in)
Weight: .............................. 8.5kg (18.7 lb)
Declarations
Regulatory Requirements
This product can only be used with American Dynamics
products.
When the unit is hard wired, the disconnect device (circuit
breaker) must be readily accessible.
Use only polarized plug/cordsets; non-polarized plugs
invalidate regulatory approvals. Use only approved cordsets.
The socket outlet must be installed near the equipment and
easily accessible.
Regulatory Compliance
REG ID: JB-SNET
FCC COMPLIANCE:
This equipment has been tested and
found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
EQUIPMENT MODIFICATION CAUTION:
Equipment
changes or modifications not expressly approved by
Sensormatic Electronics Corporation, the party responsible
for FCC compliance, could void the user's authority to operate
the equipment and could create a hazardous condition.
Other Declarations
Thank you for using American Dynamics products. We
support our products through an extensive and worldwide
network of dealers. The dealer through whom you originally
purchased this product is your point of contact if you have a
need for service or support. Our dealers are fully empowered
to provide the very best in customer service and support.
Dealers should contact American Dynamics at (800) 507-
6268 or (561) 912-6259 or on the web at
www.americandynamics.net.
WARRANTY DISCLAIMER:
Sensormatic Electronics
Corporation makes no representation or warranty with respect
to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular
purpose. Further, Sensormatic Electronics Corporation
reserves the right to revise this publication and make changes
from time to time in the content hereof without obligation of
Sensormatic Electronics Corporation to notify any person of
such revision or changes.
LIMITED RIGHTS NOTICE:
For units of the Department
of Defense, all documentation and manuals were developed at
private expense and no part of it was developed using
Government Funds. The restrictions governing the use and
disclosure of technical data marked with this legend are set
forth in the definition of "limited rights" in paragraph (a) (15)
of the clause of DFARS 252.227.7013. Unpublished - rights
reserved under the Copyright Laws of the United States.
REVSION NOTICE:
The information in this manual was
current when published. The manufacturer reserves the right
to revise and improve its products. All specifications are
therefore subject to change without notice.
TRADEMARK NOTICE:
American Dynamics,
SpeedDome, and Sensormatic are trademarks or registered
trademarks of Sensormatic Electronics Corporation. Other
product names (if any) mentioned herein may be trademarks
or registered trademarks of Sensormatic or other companies.
Trademarked names are used throughout this manual. Rather
than place a symbol at each occurrence, trademarked names
are designated with initial capitalization. Inclusion or
exclusion is not a judgment on the validity or legal status of
the term.
COPYRIGHT NOTICE:
Under copyright laws, the contents
of this document may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine-
readable form, in whole or in part, without prior written
consent of Sensormatic Electronics
© Copyright 1997–2003 Sensormatic Electronics Corporation
mhj 05/2004
