American Dynamics RAS915LS Operator'S Manual Download Page 75 | Manualshive

Page: 75 / 124

background image

Supported Controllers and Matrix Switching Systems

This section provides information about the SensorNet and RS-422 controllers and matrix switchers that are
compatible with SpeedDome Ultra VII. Refer to the controller information for details concerning specific functions
supported.

Note:

This list of controllers is complete as of the time of publication. Other controllers may be

supported. Contact your Sales Representative for current information.

Controller/Switcher Page

Number

Controller/Switcher Page

Number

•

•

•

•

•

•

•

•

•

•

•

•

VM8

Supported Protocol

SensorNet

Maximum Presets

0

Maximum Patterns

(1)

1

Quick Set Menu

Not supported

Address Range

1-8

Notes:

(1) Apple Peel only. Programmable patterns are not

available.

VM16/ADTT16 (White Touch Tracker)

Supported Protocols

SensorNet

RS-422

(1)

Maximum Presets

96 – SensorNet

4 – RS-422

Maximum Patterns

(2)

3

Quick Set Menu

Not supported

Address Range

1-16

Notes:

(1) Requires RCSN422 code converter.

(2) Patterns are limited by time and the number of

available dome commands. Total time for each
pattern cannot exceed 6 minutes 50 seconds.
Total dome commands used in the all patterns
cannot exceed 99.

VM16E/ADTT16E (Black Touch Tracker)

Supported Protocols

SensorNet

RS-422

(1)

Maximum Presets

96 – SensorNet

4 – RS-422

Maximum Patterns

(2)

3

Quick Set Menu

Yes

(3)

Address Range

1-16 or

1-64

(3)

Notes:

(1) Requires RCSN422 code converter.

(2) Patterns are limited by time and the number of

available dome commands. Total time for each
pattern cannot exceed 6 minutes 50 seconds.
Total dome commands used in all patterns cannot
exceed 99.

(3) Requires firmware version 0701-2833-0103

(EEPROM) / 0701-2834-0201 (Flash PROM) or
newer.

SensorNet and RS-422 Protocols Command Summary

A–3

«
...
73
74
75
76
77
...
»

Summary of Contents for RAS915LS





























































































































Reviews:

No comments

Related manuals for RAS915LS

Brand: Rascal Pages: 1

Brand: 2gig Technologies Pages: 10

Brand: HAI Pages: 2

Brand: Magellan Pages: 68

Brand: Magellan Pages: 2

Brand: Magellan Pages: 52

Brand: Magellan Pages: 12

Brand: Magellan Pages: 48

Brand: M-system Pages: 3

Brand: Keysight Technologies Pages: 19

Brand: HIKVISION Pages: 39

NVIP-5DN3615AV/IR-1P/F

Brand: Novus Pages: 45

Brand: 3xLogic Pages: 17

Brand: Eneo Pages: 8

Brand: Grundig Pages: 74

Brand: DSC Pages: 8

Brand: EverFocus Pages: 114

Brand: EverFocus Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands