American Dynamics RAS915LS Operator'S Manual Download Page 32

Page: 32 / 124

What To Do Next

When you select

Exit

from the

Camera Functions

screen, the

Dome Configuration Menu

appears.

DOME CONFIGURATION MENU

PAN/TILT/ZOOM/SYNC OPTS

CAMERA FUNCTIONS

ALARMS/AREAS/PRESETS/PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

From this screen you can:

Chapter 2
Chapter 3
Chapter 4
Chapter 5
Chapter 6
Chapter 7

Chapter 1

•

Select an option to make additional changes.

•

Restore settings to the factory defaults.

•

Exit the utility without saving changes.

•

Save the changes and exit the utility.

Move the highlight bar to an item and select it. Refer to the related chapter for additional information.

3–6

SpeedDome Ultra VII Operator's Manual

Summary of Contents for RAS915LS





























































































































Search results

Summary of Contents for RAS915LS

Reviews:

Related manuals for RAS915LS

Brands by name

Popular brands

American Dynamics RAS915LS, Operator'S Manual

Search results

Summary of Contents for RAS915LS

Reviews:

Related manuals for RAS915LS

Brands by name

Popular brands