background image

 

MEGAPOWER CPU ETHERNET FIRMWARE UPGRADE PROCEDURE 

8200-0813-01, REV. B0 

INSTALLATION GUIDE 

12 of 12

 

3.  Click on the 

MPCPU > Status > Monitor 

Status

 option in the tree and wait for the 

information to be filled in completely. 

4.  Verify whether or not every monitor has 

camera one selected.  If the associations have 
not been preserved (all monitors have camera 
one selected), they will have to be entered 
manually with a keyboard using the following 
procedure. 

Manual Synchronization of the Original 
ADMPCPU’s Camera to Monitor Selections 
(Now as Backup) 

1.  Launch the AD EASY CPU Configurator. 

2. Select 

MPCPU > System > Options

 and enter 

the IP address manually in the 

CPU 

Addresses

 section. 

3.  Click on the 

MPCPU > Status > Monitor 

Status

 option in the tree and wait for the 

information to be filled in completely. 

4.  Using a keyboard attached to the system, 

select each monitor and reselect the camera 
number visible in the camera number section 
of the keyboard.  Please reference the EASY 
CPU Configurator monitor status to determine 
if there were any tours loaded for particular 
monitors and initiate the corresponding tours 
once again.  Leave it running or pause it as the 
monitor status dictates. 

5.  Repeat the process for on all monitors on the 

physical site. 

Activating the Original ADMPCPU (Now as 
Backup) 

After confirming that the camera to monitor 
associations have been restored, select the 
upgraded unit as Active with the Port Module’s soft 
select switch.  Allow it to run as active sufficient 
time to ensure confidence that it is programmed 
correctly. 

Upgrading a Dual MPCPU System Using 
the Ethernet Crossover Cable 

If you have a dual MPCPU system and are using 
the direct-connect Ethernet crossover cable, move 
the connection cable to the other MPCPU, and 
repeat the above procedure. 

Declarations 

Thank you for using American Dynamics products. We 
support our products through an extensive and worldwide 
network of dealers. The dealer, through whom you originally 
purchased this product, is your point of contact if you have a 
need for service or support. Our dealers are fully empowered 
to provide the very best in customer service and support. 
Dealers should contact American Dynamics at 
(800) 507-6268 or (561) 912-6259 or on the web at 
www.americandynamics.net. 

WARRANTY DISCLAIMER:

 Sensormatic Electronics 

Corporation makes no representation or warranty with respect 
to the contents hereof and specifically disclaims any implied 
warranties of merchantability or fitness for any particular 
purpose. 

NOTICE: 

The information in this manual was current when 

published. The manufacturer reserves the right to revise and 
improve its products. All specifications are therefore subject to 
change without notice. 

LIMITED RIGHTS NOTICE:

 For units of the Department 

of Defense, all documentation and manuals were developed at 
private expense and no part of it was developed using 
Government Funds. The restrictions governing the use and 
disclosure of technical data marked with this legend are set 
forth in the definition of “limited rights” in paragraph (a) (15) 
of the clause of DFARS 252.227.7013. Unpublished - rights 
reserved under the Copyright Laws of the United States. 

TRADEMARK NOTICE:

 

American Dynamics

 and 

Sensormatic

 are trademarks or registered trademarks of 

Sensormatic Electronics Corporation. Other product names 
mentioned herein may be trademarks or registered trademarks 
of Sensormatic or other companies. 

COPYRIGHT:

 Under copyright laws, the contents of this 

manual may not be copied, photocopied, reproduced, 
translated or reduced to any electronic medium or machine-
readable form, in whole or in part, without prior written 
consent of Sensormatic Electronics. 

WJM 6/2007 

Summary of Contents for MegaPower













Reviews: