manualshive.com logo in svg

American Dryer Corp. ML-75HS, Installation Manual, Page: 31 / 56

Share
Download
American Dryer Corp. ML-75HS Installation Manual Download Page 31

27

G.  GAS INFORMATION

It is your responsibility to have 

ALL

 plumbing connections made by a qualified professional to assure that the gas

plumbing installation is adequate and conforms with local and state regulations or codes.  In the absence of such

codes, 

ALL

 plumbing connections, materials, and workmanship 

must conform

 to the applicable requirements of

the National Fuel Gas Code ANSI Z223.1-LATEST EDITION.

IMPORTANT

: Failure to comply with these codes or ordinances, and/or the requirements

stipulated in this manual, can result in PERSONAL INJURY and IMPROPER

OPERATION of the dryer.

The dryer and its individual shut-off valves 

must be

 disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).  The dryer 

must be

 isolated from

the gas supply piping system by closing its individual manual shut-off valve during any pressure test of the gas

supply system at test pressures equal to or less than 1/2 psig (3.5  kPa).

IMPORTANT:

Failure to isolate or disconnect the dryer from supply as noted can cause

irreparable damage to the gas valve

 

VOIDING THE WARRANTY.

WARNING:  FIRE or EXPLOSION COULD RESULT.

1.  Gas Supply

The gas dryer installation 

must meet

 the American National Standard...National Fuel Gas Code ANSI Z223.1-

LATEST EDITION, as well as local codes and ordinances and 

must be

 done by a qualified professional.

NOTE

: Undersized gas piping will result in ignition problems, slow drying, increased use of

energy, and can create a safety hazard.

The dryer 

must be

 connected to the type of heat/gas indicated on the dryer label affixed behind the right control

box door.  If this information does not agree with the type of gas available,  

DO NOT

 operate the dryer.

Contact the distributor who sold the dryer or the 

ADC

 factory.

IMPORTANT:  

Any burner changes or conversions 

 must be

 

made by a qualified professional.

The input ratings shown on the dryer data label are for elevations up to 2,000 feet, unless elevation requirements

of over 2,000 feet were specified at the time the dryer order was placed with the factory.  The adjustment or

conversion of dryers in the field for elevations over 2,000 feet are made by changing each burner orifice.  If this

conversion is necessary, contact the distributor who sold the dryer or contact the 

ADC

 factory.

Summary of Contents for ML-75HS

























































Reviews:

No comments