American Dryer Corp. HBG76 Installation & Operator'S Manual Download Page 1

HBG76

Installation/Operator Manual

ADC Part No. 113615 - 1

American Dryer Corporation

88 Currant Road

Fall River MA 02720-4781 USA

Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447

e-mail: [email protected]

www.amdry.com

AVERTISSEMENT: Assurez-vous de
bien suivre les instructions données dans
cette notice pour réduire au minimum le
risque d’incendie ou d’explosion ou pour
éviter tout dommage matériel, toute
blessure ou la mort.

—Ne pas entreposer ni utiliser d’essence

ni d’autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.

—QUE FAIRE SI VOUS SENTEZ UNE

ODEUR DE GAZ:

Ne pas tenter d’allumer d’appareils.

Ne touchez à aucun interrupteur.  Ne
pas vous servir des téléphones se
trouvant dans le bâtiment.

Évacuez la pièce, le bâtiment ou la
zone.

Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.

Si vous ne pouvez rejoindre le
fournisseur de gaz, appelez le service
des incendies.

—L’installation et l’entretien doivent être

assurés par un installateur ou un
service d’entretien qualifié ou par le
fournisseur de gaz.

WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion and to prevent property
damage, personal injury or death.

— Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch;
do not use any phone in your
building.

Clear the room, building or area of
all occupants.

Immediately call your gas supplier
from a neighbor’s phone.  Follow
the gas supplier’s instructions.

If you cannot reach your gas
supplier, call the fire department.

— Installation and service must be

performed by a qualified installer,
service agency or the gas supplier.

Summary of Contents for HBG76























Reviews: