(35a) (35b) GND (GROUND TERMINALS) - Connect the ground lead of the turntables with this terminal. This helps to
reduce humming and popping noises. There are two convenient ground terminals located on the rear of the mixer.
(36) MIC 3 JACK - Connect your third microphone with 1/4 inch (6.3mm) jack plug here. To use MIC 3, CH-4 LINE 5/
LINE 6/MIC 3 SWITCH (3) must be switched to MIC 3. To turn MIC 3 OFF, change the LINE 5/LINE 6/MIC 3 SWITCH to
LINE 5 or LINE 6.
(37), (38), (39), (40) LINE / PHONO / AUX INPUT JACKS - Input jack for CH-1, CH-2, CH-3 and CH-4. Connect turnta-
bles equipped with MM pickup cartridge to PHONO inputs. CD players or Tape Decks should be connected to LINE
input. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connect-
ed to LINE inputs. CHANNEL 1 (37) features left and right RCA inputs for LINE 1 and PHONO 1 / AUX 1. CHANNEL 2
(38) features left and right RCA inputs for LINE 2 and PHONO 2 / AUX 2. CHANNEL 3 (39) features left and right RCA
inputs for LINE 3, LINE 4 and PHONO 3 / AUX 3. CHANNEL 4 (40) features left and right RCA inputs for LINE 5 and
LINE 6.Other inputs (ie. CD players) may also be used in the PHONO/AUX RCA jacks(37, 38, 39) when the
PHONO/AUX SELECTOR SWITCH (41) is set to AUX.
(41) PHONO / AUX SELECTOR SWITCH - Changes phono to an extra line; allows the DJ to use a CD player or other
input device in the same line as the phono line. When using a turntable select PHONO, and when using other input
devices select AUX. PHONO/AUX lines can be used with LINES 1, 2, and 3. The PHONO /AUX SELECTOR SWITCH
gives the DJ the possibilities of 3 extra inputs lines (ie. 3 lines CD, tape etc.).
(42) INDEPENDENT LIGHT CONTROL - Buffered audio output for light controllers that can use external input. Great for
Touch Panels and Chase Controllers.
(43) MASTER OUT - Parallel output of P.A. output. Connect with the input of a power amplifier. Make sure that the
STEREO/MONO switch (32) is set to STEREO.
(44) REC OUT - Connect to your record unit. The REC OUT level is not influenced by the MASTER FADER (31).
(45) ZONE 1 & ZONE 2 OUTPUTS - Left & Right RCA output jacks controlled by the ZONE 1 & ZONE 2 (24, 25, 26)
controls on the front panel.
(46) SEND & RECEIVE EFFECTS - Left & Right 1/4” stereo jacks for SEND (27) & RECEIVE (28) EFFECTS.
(47) BALANCED OUTPUT - Balanced output for the master signal.
(48) AC CONNECTION - Standard IEC plug with detachable AC power cord.
(49) FUSE - Fuse holder. Only replace the fuse when the device is disconnected from main power supply. Only replace
with fuses of the same power rating.
(50) AC VOLTAGE SELECTOR - Select between 115V/50Hz or 230V/60Hz. Make sure that the selector is set to the
proper voltage you are using.
XDM-3633 User Instructions page 7
LINE 1
CH-1
PHONO 1
AUX 1
LINE 2
CH-2
PHONO 2
AUX 2
MASTER
OUTPUT
REC
L
R
50
AUX 2 PHONO 2
AUX 1 PHONO 1
47
GND
LIGHT CONTROL
42
41
35b
CH-3
CH-4
MIC 3
PHONO 3
AUX 3
LINE 3
LINE 4
ZONE 1
ZONE 2
LINE 5
LINE 6
SEND
EFFECT
RECEIVE
BALANCED OUTPUT
RIGHT
LEFT
AUX 3 PHONO 3
115V
AC VOLTAGE
SELECTOR
AC INPUT
115/230V
FUSE
Inputs and Outputs (Rear Panel)
GND
49
48
46
45
44
40
43
39
38
37
38
35a
