Power Supply:
Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your American
DJ
®
Spektra 250™ before attempting operation.
General Operation:
Just plug this light in, and watch it go. This
fixture is designed to operate as a stand alone unit. It has been tested
and the lamp has been installed at the factory, there is no assembly
necessary. The Spektra 250™ is ready to be plugged in, out of the
box, there is no power switch. If there is no lamp output check the
breaker and bulb. If the breaker and bulb are good, please return the
unit for servicing.
Operating Modes:
This unit comes with two 3-way multi-operating switches located on
the rear of the unit. The switches each have three (3) different operat-
ing modes.
The top Switch will control the textured glass wheel.
Switch in the "I" position: Mode 1 - In this mode the textured glass
wheel will spin continuously, regardless of the presence of sound.
Switch in the “0” position: Mode 2 - In this mode the textured glass
wheel will remain static.
Switch in the “II” position: Mode 3 - In the this mode the textured
glass wheel will only rotate in the prescence of sound. Please note
that tapping on the unit, or high pitched sounds may not trigger the
unit, the unit is designed to react to low frequencies (bass). Also note
that the music sensitivity is preset at the factory and may not be
changed or adjusted.
The bottom switch will control the Color Arm.
Switch in the "I" position: Mode 1 - In this mode the color arm will
move continuously, regardless of the presence of sound.
Switch in the “0” position: Mode 2 - In this mode the color arm will
remain static.
Switch in the “II” position: Mode 3 - In the this mode the color arm
will only move in the prescence of sound.
Spektra 250™
Operation
©
American DJ
®
- www.americandj.com - Spektra 250™ Instruction Manual Page 6
©
American DJ
®
- www.americandj.com - Spektra 250™ Instruction Manual Page 5
Spektra 250™
Lamp Replacement
Caution:
Always replace with the exact same type lamp, unless oth-
erwise specified by an authorized American DJ
®
technician. Replace
with anything other than the specified part can damage your unit and
will void your manufactures warranty.
Warning:
If you continue to blow either the lamp or the breaker,
STOP using the unit. Contact customer support for further instruc-
tions, you may have to return the unit for servicing. Continuing to use
the unit may cause serious damage.
Breaker Reset:
This unit is equipped with a built-in safety breaker.
This breaker is designed to close the power circuit in the event of an
internal short or power surge. This will reduce the risk of electrical
shock or fire and protect the circuitry. To reset the breaker, push the
breaker button in until you hear it “pop” back in to place. If the break-
er continues to pop, stop using the unit and contact our customer
support team, the unit may need to be returned for service
.
Lamp Replacement:
Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power
and allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up front cover that is retained by a thumb screw.
1. Be sure to follow the proper handling procedures that deal with
halogen lamps.
2. Remove the thumb screw on the top front of the unit.
3. After removing the thumb screw, pull off socket assembly protec-
tive cover.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble in reverse
order.
Halogen Lamp Warning:
This fixture is fitted
with halogen lamps which are highly susceptible
to damage if improperly handled. Never touch the
lamps with your bare fingers as the oil from your
hands will shorten lamp life. Also, never move the
fixture until the lamps have had ample time to cool.
Remember, lamps are not covered under warranty
conditions.