©
American DJ Supply
®
- www.americandj.com - Saga II™ Instruction Manual Page 4
©
American DJ Supply
®
- www.americandj.com - Saga II™ Instruction Manual Page 3
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Saga II™
General Instructions
Saga II™
Safety Precautions
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electri-
cal shock and fire in case of an internal short.
• Do not remove the unit cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
fixture.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer.
• The fixture should be serviced by qualified service personnel
when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
m arked change in performance.
Saga II™
Operation
Power Supply:
Before plugging your unit in, be sure the source voltage in your
area matches the required voltage for your American DJ
®
Saga II.™
The American DJ
®
Saga II
™
is available in a 120v and 220v version.
Because line voltage may vary from venue to venue, be sure to plug
your fixture into a wall outlet with a matching power supply before
attempting to operate.
General Operation:
This fixture is designed to operate as a stand alone unit, there is no
need of a controller. The Saga II™ is ready to be plugged in, out of
the box. If there is no lamp output check the breaker and bulb. If the
breaker and bulb are good, please contact our toll free customer sup-
port number for further instructions. Please do not return the unit to
your dealer without first contacting customer support.
Mode Switches:
The Sage come with two mode switches on the rear of the unit.
Switch 1 controls the reflector dish, switch 2 controls the gobo wheel.
When the switches are in the up position (“I”) the wheels will rotate in
a continuous rotation regardless of sound. When the switches are in
the middle position (“0”) the wheels will remain static (no rotation).
When the switches are in the down position (“II”) the wheels will react
to sound. Each wheel may be operated separately, so one wheel may
be controlled by sound while the other may be in a rotating in con-
tinuous motion.
Saga II™
Warranty Registration
The Saga II™ carries a one year (365 days) limited warranty. Please
fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. The
R.A. number must be clearly written on the outside of the return
package. A brief description of the problem as well as the R.A. num-
ber must also be written down on a piece of paper and included in
the shipping container. If the unit is under warranty, you must provide
a copy of your proof of purchase invoice. You may obtain a R.A. num-
ber by contacting customer support at (800) 322-6337.
