American DJ Revo Roll LED User Instructions Download

Page: 4 / 8

American DJ

- www.americandj.com - Revo Roll LED™ Instruction Manual Page 7

American DJ

- www.americandj.com - Revo Roll LED™ Instruction Manual Page 8

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-
dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.

Conductor

5-Pin XLR Male (In)

3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Revo Roll LED™

Set Up

Revo Roll LED™

System Menu

ADDR -

DMX Address Setting

1. Tap the either the MENU, UP, or DOWN buttons until “

ADDR

”

is displayed, press ENTER.

2. A number between 1-512 will be displayed and flashing.
Press the UP or DOWN buttons to find your desired address.

Press ENTER to set your desired DMX address.

SLND -

This will let you set unit as a master or slave in a

master/slave configuration.

1. Tap the either the MENU button until “

SLND

” is displayed,

press ENTER. “

MSTR

”, “

SL 1

” or “

SL 2

” will be displayed.

2. Tap the UP or DOWN buttons until your desired setting is

displayed, press ENTER to confim and exit.

BLND -

Blackout or Stand by mode.

1. Tap the either the MENU button until “

BLND

” is displayed,

press ENTER. Either Yes or No will be displayed.
2. To activate Blackout tap the UP or DOWN buttons until Yes is

displayed, press ENTER to confim and exit. The fixture will now

be in Blackout mode. To deactivate Blackout mode, select No
and press Enter.

I PAN -

Pan Inversion

1. Tap the either the MENU button until “

I PAN

” is displayed,

press ENTER. Either NO or 1 will be displayed.

2. To activate the Pan inversion tap the UP or DOWN buttons
until

is displayed, press ENTER to confim and exit. To deacti

vate Pan inversion, select No and press Enter.

Summary of Contents for Revo Roll LED









Search results

Summary of Contents for Revo Roll LED

Reviews:

Related manuals for Revo Roll LED

Brands by name

Popular brands

American DJ Revo Roll LED, User Instructions

Search results

Summary of Contents for Revo Roll LED

Reviews:

Related manuals for Revo Roll LED

Brands by name

Popular brands