Reflex™
Fuse & Lamp Replacement
Caution:
Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ
®
techni-
cian. Replace with anything other than the specified part can damage
your unit and will void your manufactures warranty.
Warning:
If after you have replaced the lamp or fuse and you con-
tinue to blow either one, STOP using the unit. Contact customer sup-
port for further instructions, you may have to return the unit for ser-
vicing. Continuing to use the unit may cause serious damage.
Fuse Replacement:
Disconnect the unit’s main power supply.
Insert a standard flat head screw driver in to the fuse holder housing
(located on the bottom of the unit). Turn the screwdriver in a coun-
ter-clockwise direction to remove the fuse holder. Remove the old
fuse and discard it, replace the fuse with the same type. Insert the
fuse holder back into it’s housing and turn in a clockwise direction to
secure the holder in place.
Lamp Replacement:
Caution! Never open the unit when in use.
Always disconnect the main power and allow the fixture ample time
to cool before attempting to replace the lamp. Lamp replacement has
been made simple by incorporating a remove tray that is retained by
a single thumb screws. Again, please remember to always replace
with the exact same type lamp.
1. Be sure to follow the proper procedures when handling halogen
lamps. Never touch the new lamp with your bare fingers.
2. Unscrew the single thumb screw located on the rear of the unit.
3. Once the thumb screw has been remove, pull back the lamp
assembly cover plate to expose the lamps.
4. Remove and replace the lamp with an exact match.
5. Reassemble in reverse order.
©
American DJ
®
- www.americandj.com - Refl ex™ Instruction Manual Page 6
©
American DJ
®
- www.americandj.com - Refl ex™ Instruction Manual Page 5
Halogen Lamp Warning!
This fixture is fitted with
halogen lamps which are highly susceptible to dam-
age if improperly handled. Never touch the lamps
with your bare fingers as the oil from your hands will
shorten lamp life. Also, never move the fixture until
the lamps have had ample time to cool. Remember,
lamps are not covered under warranty conditions.
Fixture Cleaning:
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal lenses and dichroic colored dishes should be carried out periodi-
cally to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a soft brush to clean out the cooling vents
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-
mend cleaning on a monthly basis. Periodic cleaning will ensure lon-
gevity, and crisp beam output.
Reflex™
Cleaning
Trouble Shooting:
Listed below are a few common problems and solutions you should
try before contacting customer support. For all other issues please
contact customer support.
Unit rotates but has no light output from the unit;
1. Be sure you have connected your unit into a matching wall outlet.
2. Remove the lamp cover and be sure the lamps are seated in their
sockets properly. Occasionally lamps become loose during ship-
ping be sure the lamps are push in to their sockets all the way.
3. Be sure the lamps are good.
Heads do not rotate and lamps do not turn on;
1. Be sure you have connected your unit into a matching wall outlet.
2. Be sure the external fuse has not blown. The fuse holder is locat-
ed on the bottom panel of the unit.
3. Be sure the unit power cord is properly seated in the power outlet
and the outlet has power.
4. Be sure the fuse holder is completely screwed in
Reflex™
Trouble Shooting
