American DJ Quad Phase Go User Instructions Download Page 9

Page: 9 / 12

Quad Phase Go

DMX Traits

Channel

Value

Function

1 0 - 255 COLOR SELECTION

1 - 16 COLOR 1

17 - 33 COLOR 2

34 - 50 COLOR 3

51 - 67 COLOR 4

68 - 84 COLOR 5

85 - 101 COLOR 6

102 - 118 COLOR 7

119 - 135 COLOR 8

136 - 152 COLOR 9

153 - 169 COLOR 10

170 - 186 COLOR 11

187 - 203 COLOR 12

204 - 220 COLOR 13

221 - 237 COLOR 14

238 - 255 COLOR 15
2 ROTATION
0 - 9 NO ROTATION

10 - 120 CLOCKWISE FAST - SLOW

121 - 134 NO ROTATION

135 - 245 COUNTER-CLOCKWISE

SLOW - FAST

246 - 249 NO ROTATION

250 - 255 SOUND ACTIVE
3 STROBING

0 OFF

1 - 255 STROBING SLOW - FAST
4 SHUTTER OPEN

0 - 15 OFF

16 - 255 OPEN

ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 17

ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 18

Quad Phase Go

Battery Status & Charging

Battery Status:

This function is used to check the life status of the battery.

Plug the fixture in and press the MODE button until “BATT” is

displayed. Use the UP or DOWN buttons to scroll to “STAT”

and press ENTER. The number that is displayed is the remain-

ing battery life. Please do not let the battery fully die, this

severly shortens the life of the battery.
Example: If “50” is displayed, the battery is at half life. If “25” is

displayed, the battery is at 25% life.
NOTE: When the battery is charging or if the battery life is

below 30% the digital display will flash.

Battery Recharge: To recharge the battery, plug the supplied

AC cord into the AC input on the side of the unit and plug the

other end into a matching power supply.

Press the MODE button until “BATT” is displayed, and press

ENTER.
Use the UP or DOWN buttons to scroll to the menu “CHAR”

then press ENTER.
Use the UP or DOWN buttons to scroll to “ON”, and press

ENTER. The after you select “ON” the battery is now being

charged. To stop charging the battery, select “OFF”.
If the battery is being charged, and the unit is not being used,

press the MODE button until “BATT” is displayed, and press

ENTER. Use the UP or DOWN buttons to scroll to “LOAD” and

press ENTER. Select “ON” to keep the LED on, or “OFF” to

blackout the unit.
It takes about 6 hours to reach full charge.

Note: When unplugging the unit from charging and then

applying power via battery, there will be a minimal charge

drop.

Summary of Contents for Quad Phase Go













Search results

Summary of Contents for Quad Phase Go

Reviews:

Related manuals for Quad Phase Go

Brands by name

Popular brands

American DJ Quad Phase Go, User Instructions

Search results

Summary of Contents for Quad Phase Go

Reviews:

Related manuals for Quad Phase Go

Brands by name

Popular brands