MULTI-STAR II™
Fuse & Lamp Replacement
Caution:
Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ
®
techni-
cian. Replace with anything other than the specified part can damage
your unit and will void your manufactures warranty.
Warning:
If after you have replaced the lamp or fuse and you con-
tinue to blow either one, STOP using the unit. Contact customer sup-
port for further instructions, you may have to return the unit for ser-
vicing. Continuing to use the unit may cause serious damage.
Fuse Replacement:
Disconnect the unit’s main power supply. Use
a number 2 Phillips screw driver in to the fuse holder housing (located
on the bottom of the unit). Turn the screwdriver in a counter-clock-
wise direction to remove the fuse holder. Remove the old fuse and
discard it, replace the fuse with the same type. Insert the fuse holder
back into it’s housing and turn in a clockwise direction to secure the
holder in place.
Lamp Replacement:
Caution! Never open the unit when in use.
Always disconnect the main power and allow the fixture ample time
to cool before attempting to replace the lamp. Lamp replacement has
been made simple by incorporating a remove tray that is retained by
a single thumb screws. Again, please remember to always replace
with the exact same type lamp.
1. Be sure to follow the proper procedures when handling halogen
lamps. Never touch the new lamp with your bare fingers.
2. Unscrew the three thumb screws that secure the outer half of the
dome cover to the inner half.
3. Once the thumb screws have been removed, remove the outer
half of the dome assembly to expose the lamps.
4. Remove and replace the lamp with an exact match.
5. Reassemble in reverse order.
©
American DJ
®
- www.americandj.com - MULTI-STAR II™ Instruction Manual Page 5
Halogen Lamp Warning!
This fixture is fitted with
halogen lamps which are highly susceptible to dam-
age if improperly handled. Never touch the lamps
with your bare fingers as the oil from your hands will
shorten lamp life. Also, never move the fixture until
the lamps have had ample time to cool. Remember,
lamps are not covered under warranty conditions.
©
American DJ
®
- www.americandj.com - MULTI-STAR II™ Instruction Manual Page 4
MULTI-STAR II™
Operation
Power Supply:
Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your American
DJ
®
MULTI-STAR II™ before attempting operation.
General Operation:
Just plug this light in, and watch it go. This fix-
ture is designed to operate as a stand alone unit. It has been tested
and the lamp has been installed at the factory there is no assembly
necessary. The MULTI-STAR II™ is ready to be plugged in, out of the
box. There is no power switch, after plugging the unit in the base and
five outer heads will immediately begin to spin.
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte-
nance of this unit. Please keep this manual with the unit, for future
reference.
MULTI-STAR II™
General Instructions
Fixture Cleaning:
Due to fog residue, smoke, and dust cleaning the
internal and external lenses should be carried out periodically to opti-
mize light output. Cleaning frequency depends on the environment
in which the fixture operates (I.e. smoke, fog residue, dust, dew).
In heavy use we recommend cleaning on a monthly basis. Periodic
cleaning will ensure longevity, and crisp beam output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a soft brush to clean out the air vents
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
MULTI-STAR II™
Cleaning
