©
American DJ
®
- www.Americandj.com - Flat Par Tri18X User Manual Page 11
©
American DJ
®
- www.Americandj.com - Flat Par Tri18X User Manual Page 12
Flat Par Tri18X ADJ LED RC Operation
The
ADJ LED RC
infrared remote
(sold seperately) has many differnet
functions and gives you complete control of your Flat Par Tri18X. To
control the your desired fixture you must aim the controller at the front
of the fixture and be no more the 30 feet away. To use the ADJ LED
RC you must first activate the fixtures infrared receiver, to activate the
receiver please see the instructions on page 10.
BLACKOUT
-
Pressing this button will blackout the fixture.
AUTO RUN
-
This button will run an automatic program. You can con-
trol the speed of the Auto Run by pressing the SPEED button first and
then pressing the “+” and “-” buttons.
PROGRAM SELECTION
-
This button will let you access the units
built-in programs. Pressing this button and then press the “+” or “-”
to navigate through the built-in programs.
FLASH
-
This button will activate the strobe effect. You can control
the flash rate by pressing the “+” and “-” buttons. Press this button
again to exit strobe mode.
SPEED
-
Press this button and use the “+” & “-” buttons to adjust the
speed of the Auto run.
DMX MODE -
This button will let you select which DMX mode you
want to use. Some fixtures will come with different DMX channel
modes. This button will switch between the different modes. Please
see pages 13-16 for DMX modes, values, and traits.
SOUND ACTIVE -
This button activates sound active mode.
SLAVE -
This designates the fixture as a slave fixture in a master/
slave configuration.
SET ADDRESS -
Press this button to set the DMX address. Press this
button first, then press the numbers to set the address.
Example: Set DMX Address 1 Press “S-0-0-1”
Set DMX Address 245 Press “S-2-4-5”
R G B -
Press either one of these buttons and the press the “+” or “-”
to adjust the brightness.
“+” and “-” -
Use these buttons to adjust the flash rate, speed of the
Auto Run, sound sensitivity, and program selection.
DMX Control:
Operating through an DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
Follow the directions below to set your DMX Mode and address.
1. Before connecting to an DMX controller, your fixture has different
DMX channel modes, please select your desired mode by press-
ing the DMX Mode button, then using the “+” or “-” buttons to
scroll through the DMX Channel Modes. Set the mode before you
address the fixture. See the bottom of this page for the DMX
modes.
2. After you have selected your mode, set the DMX address for the
fixture by pressing the “S” button. When the “S” button is pressed
the LED’s will flash 2-3 times and all the red LED’s will light. Use
the number buttons to press in your desired address. See “SET
ADDRESS” on page 11 for examples.
Note: When seeting the DMX address each time a number is pressed
a LED color will glow, when you have set the DMX address correctly
all LED’s will flash 2-3 times.
3. Now you may connect the fixture via the XLR connections to any
standard DMX controller. Please see pages 13-16 to for a detailed
descriptions of the DMX modes, values, and traits.
• If the Red LED’s glow you are in DMX Mode 1: 1 DMX Channel.
• If the Green LED’s glow you are in DMX Mode 2: 2 DMX
Channels.
• If the Blue LED’s glow you are in DMX Mode 3: 3 DMX Channels.
• If the Red & Green LED’s glow you are in DMX Mode 4: 4 DMX
Channels.
• If the Red & Blue LED’s glow you are in DMX Mode 5: 5 DMX
Channels.
• If the Green & Blue LED’s glow you are in DMX Mode 6: 6 DMX
Channels.
• If all of the LED’s glow you are in DMX Mode 7: 7 DMX
Channels.
Flat Par Tri18X ADJ LED RC Operation
