©
American DJ Supply
®
- www.americandj.com - Dual Gem LED™ Instruction Manual Page 4
©
American DJ Supply
®
- www.americandj.com - Dual Gem LED™ Instruction Manual Page 3
Dual Gem LED™
Precautions
Safety Issue:
This unit may blow the breaker if the maximum allotted
load of 2 amps is reached. If the fuse needs replacement, please see
the fuse replacement guidelines on page 5.
• Be sure the local power outlet match the required voltage of the
unit.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no
user serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-Cord Protection - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the fixture. Do not attempt to remove or break off the ground prong
from the electrical cord. This prong is used to reduce the risk of
electrical shock and fire in case of an internal short.
• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
Dual Gem LED™
Operation
Introduction:
The American DJ
®
Dual Gem
LED™
is a dual output
LED moon-flower effect. This fixture is designed for mobile DJ’s, clubs,
bands, roller rinks and any arena that requires a compact, light weight,
easy to use unit.
Power Supply:
Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ
®
Dual Gem LED™ before attempting operation.
General Operation:
This fixture is designed to operate as a stand
alone sound active unit, there is no need of a controller. It has been
tested and there is no assembly necessary. The Dual Gem LED™
is ready to be plugged in out of the box, there is no power switch.
When this fixture is plugged in, the units two LED panels will start
to project preset designs, all to the sound of an audio source via an
internal microphone. The audio sensitivity is preset at the factory for
optimum performance and is not user adjustable. After plugging the
unit if there is no LED output check the breaker. If the breaker has
not popped, please contact customer support for further instructions.
This fixture features a light weight case design and an adjustable
hanging bracket.
Dual Gem LED™
Breaker Reset
Dual Gem LED™
Warranty Registration
The Dual Gem LED™ carries a three year (1095 days) limited war-
ranty. Please fill out the enclosed warranty card to validate your
purchase. All returned service items whether under warranty or not,
must be freight pre-paid and accompany a return authorization (R.A.)
number. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact American DJ
®
customer
support for a R.A. number.
This unit is equipped with a built-in safety breaker. This breaker is
designed to close the power circuit in the event of an internal short
or power surge. This will reduce the risk of electrical shock or fire and
protect the circuitry. To reset the breaker, push the breaker button in
until you hear it “pop” back in to place. If the breaker continues to pop,
stop using the unit and contact our customer support team, the unit
may need to be returned for service.
