background image

©American Audio®  -  www.americanaudio.us  -  V Series™ Power Amplifier User Manual  Page 12

Mono Subwoofer - This operation is similar to the Stereo Subwoofer operation but in mono. When running subwoofers it is usually 

recommended to run them in mono mode to achieve a cleaner tighter low end. This operation allows you to run several subwoofers 

down to a minimum of 4 ohms. To avoid amplifier  overheating, never run the amplifier  below 8 ohms in this mode. Set up this mode 

as you would a standard stereo set up. In this mode you may use the frequency adjustment on the rear of the amp, to control the bass 

frequency output level. Frequencies may be adjusted from 20Hz to 200Hz.

PROTECTION:

Limiter - The amps come with a built in limiter. When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this 

time, the master volume should be lowered to reduce distortion. If the input gain level is not reduced the built-in limiter will activate. 

During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping. A limiter takes the gain 

of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and ampli-

fier. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inau-

dible. It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. During excessive clipping the 

limiter will reduce the audio signal enough to minimize the amount of clipping. When the input signal decreases enough that clipping 

ends, the limiter will deactivate and cease its gain reduction. The limiter has a fixed threshold and can not be adjusted. 
Safe Power Levels at Different Output Loads:

8-Ohm Loads: The amplifier can operate at practically any power level without risk of overheating. However, if it is pushed hard 

enough to continually light the “CLIP ” indicator, the V4002 average output power can reach 3200 watts, the V5002 can reach 4000 

Watts, and the V6002 can reach 5000 Watts.
4-Ohm Loads: If the “CLIP” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity. If it is 

lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes.
Short Circuit Protection -

 

The V Series amplifiers all come with built-in Output Short Circuit Protects. The Output Short Circuit 

Protection protects the output devices of the amplifier from short circuits and stressful loads. If your speaker lines short, the ampli-

fier automatically detects this problem and discontinues operation for that channel. If one side of your amplifier becomes shorted and 

goes into protect mode, the other side will continue to operate normally. During short circuit protection, the "Clip" LED and “Protect" 

LED will light simultaneously indicating amplifier fault. All channel output  during the “Short Circuit Protection" will be interrupted (i.e. 

no sound out

Summary of Contents for V4002



















Reviews: