background image

OVERLAY DESIGN AND LAYOUT: 
 
Graphic overlays (picture cards) can be changed easily by simply sliding the overlay through the slot on the right side of the 
housing grid.  There are several methods you can use to make overlays for the Tech-Scan32 Plus ECU.  Options include: 

1.

 

Draw or print corresponding icons or words on a sheet of 6” x 13 ¼” paper.  Section each icon so that it appears in each of 
the 32 message switch cutouts 

2.

 

Develop custom overlay using Mayer Johnson’s BOARDMAKER™ Software. 

CLEANING THE TECH-SCAN 32 PLUS ECU: 

 

Note:

  DO  NOT  SUBMURGE  THE  TECH-SCAN  32  PLUS  ECU  INTO  WATER  OR  ALLOW  WATER  TO  ENTER  THE 

EXTERNAL  SPEAKER,  RECORD  JACK  OR  SPEAKER  HOLES.    THE  TECH-SCAN  32  PLUS  ECU  IS  WATER  RESISTANT-
NOT WATERPROOF. 

1.

 

Turn the Tech-Scan 32 Plus ECU to the 

off

 position. 

2.

 

Remove the overlay from the switch grid.  

3.

 

Use a wet wash cloth and mild soap to

 

wipe the soiled areas clean.  

4.

 

Use a wet sponge with cold water to wipe the soapy areas. 

CARE AND MAINENANCE

 

The Tech-Scan32 Plus ECU is designed to automatically enter a sleep mode after a message is played.  The sleep mode is still 
an active mode and will affect battery life. If the Tech-Scan32 Plus ECU is not going to be used for a long period of time (2 to 3 
hours) it is recommended that the unit be turned off. 

If the Tech-Scan32 Plus ECU should fail to operate, or operate incorrectly, follow these steps: 

1.

 

Check to see if the Tech-Scan 32 Plus ECU is ON and if a message has been recorded at that level.  

2.

 

Make sure there are no obstacles blocking the message membrane square. 

3.

 

Turn the Tech-Scan32 Plus ECU OFF for 15 Seconds, then turn it back ON and try playback again. 

4.

 

Make sure that the batteries in the Tech Scan 32 Plus ECU are fully charged. 

5.

 

Remember – SCAN mode will not function without the external User switch. 

6.

 

For further assistance, feel free to contact our technical support team at 1-888-353-AMDI (2634).

 

 

95

 

S

HERWOOD 

A

VE

,

 

F

ARMINGDALE 

NY

 

11735 

P

HONE

:

  

(631)531-8888

    

F

AX

:

  

(631)

 

631-8811 

 

1-888-353-AMD

I

 

http://www.amdi.net 

 

Summary of Contents for TECH-SCAN32 PLUS








Reviews: