background image

References

For the full power, electrical, mechanical, and thermal specifications of the T2 card, see the T2
Telco Accelerator Card Data Sheet
 (

DS1000

).

These documents provide supplemental material useful with this guide:

1. T2 Telco Accelerator Card Installation Guide (

UG1527

)

2. Vivado Design Suite User Guide: Using Constraints (

UG903

)

Revision History

The following table shows the revision history for this document.

Section

Revision Summary

06/15/2022 Version 1.0

Initial release.

N/A

Please Read: Important Legal Notices

The information disclosed to you hereunder (the "Materials") is provided solely for the selection
and use of Xilinx products. To the maximum extent permitted by applicable law: (1) Materials are
made available "AS IS" and with all faults, Xilinx hereby DISCLAIMS ALL WARRANTIES AND
CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING BUT NOT LIMITED TO
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR ANY
PARTICULAR PURPOSE; and (2) Xilinx shall not be liable (whether in contract or tort, including
negligence, or under any other theory of liability) for any loss or damage of any kind or nature
related to, arising under, or in connection with, the Materials (including your use of the
Materials), including for any direct, indirect, special, incidental, or consequential loss or damage
(including loss of data, profits, goodwill, or any type of loss or damage suffered as a result of any
action brought by a third party) even if such damage or loss was reasonably foreseeable or Xilinx
had been advised of the possibility of the same. Xilinx assumes no obligation to correct any
errors contained in the Materials or to notify you of updates to the Materials or to product
specifications. You may not reproduce, modify, distribute, or publicly display the Materials
without prior written consent. Certain products are subject to the terms and conditions of
Xilinx's limited warranty, please refer to Xilinx's Terms of Sale which can be viewed at 

https://

Appendix B: Additional Resources and Legal Notices

UG1496 (v1.0) June 15, 2022

 

www.xilinx.com

T2 Telco Accelerator Card User Guide

 28

Send Feedback

Summary of Contents for XILINX T2 Telco






























Reviews: