background image

Installation

6

7

Mounting the Exhaust Pipe

•  The supplied Exhaust Hose can be

extended from 1 foot to 5 feet
for mounting. It is recommended that
you use the shortest possible length of Hose.

•  Take care to prevent any kink or

bend in the middle of the Exhaust
Hose, as this will trap hot exhaust air,
which will radiate back into the room.

Cleaning the Filter

Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters
and then rinse them thoroughly under running water (no hotter than 104ºF)

Dry thoroughly before replacing.

Notice! Never operate the unit without the filters.

Installation

Window Kit Installation

In order for this unit to function
properly, it must be vented to the
outside.

Fitting the Exhaust Hose through
the window is easy.  Please see
below.

1.  Extend Hose at least 6" and 

insert it into back of the unit,
tightening into place by turning
it clockwise.

2.  Attach Slide Bar Connector, 

(Round Connector) to the 
other end of the Hose by 
extending hose at least 6".  
Then tighten Hose by turning
the (Round Connector) 
clockwise.

3.  Place Adjustable Slide Bar in 

the window and expand so it
fits tightly.

4.  Lower the window.

5.  Make sure the Hose has

no kinks.

Slide Bar has 3 sections which
allows installation in windows up
to 48" in width.

Wall Connection

1. Make a hole (5.1" in diameter)

in the wall.

2. Insert the Round Connector

(part #13) into the hole and
hold in place by using 4 small
screws (not supplied).

3. Extend one end of the Exhaust

Pipe (part #11) and screw into
the Round Connector by
turning clockwise.

4. Extend other end of exhaust

pipe and screw in Adaptor (part
#10) by turning clockwise.

5. Push Adaptor to fit firmly

over the opening on the back
of the unit.

** When not in use, cover the

Round Connector and hole
with Cap (part #14).

Slide Bar

Connector

Round
Connector

WARNING!

The length of the Exhaust Pipe is specially
designed according to the specification of
this product.

Do not replace or extend it with your own hose
as this could cause the unit to malfunction.

Summary of Contents for 000E/EH









Reviews: