Ambient ACC 501 User Manual Download Page 8 | Manualshive

Page: 8 / 21

background image

experience quality

.

ACC501

Rev. 1.10.0031

www.ambient.de/en

7

6.

Menus

6.1 CONF menu

This is a general menu for the controller status and control and monitoring of peripherals.
Select option by pressing corresponding number.

1: Display:

Change display contrast and default backlight brightness and switch off time

.

2: Infrared:

Displays transceived ASCII characters, allows for a test and reset.

3: Power supply:

Shows voltages at power inputs

4: System Info:

Shows the serial number of the unit and the software versions of the various modules currently loaded.
Upon start up, the ACC501 checks if a ACCSI (Ambient Serial Interface) is connected and displays the
firmware version:

Please note: From board revision “A” on the revision is displayed next to the serial
number.

«
...
6
7
8
9
10
...
»

Summary of Contents for ACC 501






















Reviews:

No comments

Related manuals for ACC 501

Concord express

Brand: GE Pages: 3

ESSENSSE NEO COMFORT

Brand: 2VV Pages: 21

AirGENIO SUPERIOR

Brand: 2VV Pages: 27

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Brand: Nacon Pages: 24

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Brand: Eaton Pages: 96

Travel About Series

Brand: Kolcraft Pages: 14

Brand: Miller-Leaman Pages: 18

Brand: Viking Pages: 4

GA Figure 220-D

Brand: Vag Pages: 6

Brand: McIntosh Pages: 60

Brand: Ruida Technology Pages: 45

Brand: IMG STAGELINE Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands