background image

 

Version 1.0  

 

©Copyright 2013, Ambient LLC. All Rights Reserved. 

 

 

 

Page 8 

6

 

Troubleshooting Guide 

If your question is not answered here, you can contact us as follows: 
 

1.

 

Email Support: 

[email protected]

 

2.

 

Live Chat Support: 

www.ambientweather.com/chat.html

 (M-F 8am to 4pm Arizona Time) 

3.

 

Technical Support: 480-346-3380 (M-F 8am to 4pm Arizona Time) 
 
 

Problem 

Solution 

Wireless remote not reporting in to 
console. 
 
There are dashes (--.-) on the display 
console. 

The maximum line of sight communication range is 150’ 
and 100’ under most conditions. Move the sensor closer 
to the display console. 
 
If the sensor assembly is too close (less than 5’), move 
the sensor assembly away from the display console. 
 
Make sure the remote sensor LCD display is working 
and the transmitter light is flashing once per 60 seconds. 
 
Install a fresh set of batteries in the remote thermometer. 
For cold water environments, install lithium batteries. 
 
Make sure the remote sensors are not transmitting 
through solid metal (acts as an RF shield), or earth 
barrier (down a hill). 
 
Move the display console around electrical noise 
generating devices, such as computers, TVs and other 
wireless transmitters or receivers. 

LCD display fading or unreadable. 

Replace batteries in the thermometer. 
 
Extreme heat or cold will cause the display to fade but 
does not affect the wireless functionality. Bring into 
house to restore display. 

7

 

Liability Disclaimer 

Please help in the preservation of the environment and return used batteries to an authorized depot.   
The  electrical  and  electronic  wastes  contain  hazardous  substances.  Disposal  of  electronic  waste  in 
wild country and/or in unauthorized grounds strongly damages the environment. 
 
Reading the “User manual” is highly recommended. The manufacturer and supplier cannot accept any 
responsibility for any incorrect readings and any consequences that occur should an inaccurate reading 
take place. 
 
This product is designed for use in the home only as indication of weather conditions. This product is 
not to be used for medical purposes or for public information. 
 
The specifications of this product may change without prior notice. 
 
This product is not a toy. Keep out of the reach of children. 
 

Summary of Contents for F007TP











Reviews: