background image

 

WARRANTY FOR PRODUCTS MANUFACTURED AFTER 1

st

, 2016

 

Amantii Imports Corp. (“Amantii”) warrants that your newly purchased Amantii electric fireplace is free from 

manufacturing and material defects for a period of two (2) years from the date of the first purchase, subject to 

the conditions and limitations contained below. 

 

Warranty Application & Exclusions 

This limited warranty applies to your newly purchased Amantii electric fireplace; the limited warranty’s 

application is limited to purchases made in any province of Canada or in any of the 52 States of the United 

States of America, including the District of Columbia. Only the original purchaser of the product is eligible for 

coverage under this limited warranty; the warranty is not transferable. 

 

Products excluded from this limited warranty 

Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner/purchaser. 

Amantii does not cover service or labor charges. 

 

Warranty Coverage and Team 

Products covered by this limited warranty have been tested and inspected prior to shipment and subject to the 

terms & conditions of this warranty, Amantii warrants such products to be free from defects in material and 

workmanship for a period of two(2) year from the date of the first purchase. 

 

The limited two (2) year warranty period for this product also applies to any implied warranties that may exist 

under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the 

above limitation may not apply to the purchaser. 

 

All other warranties - expressed or implied - with respect to the product, its components and accessories or any 

obligation/liabilities on the part of Amantii are hereby expressly excluded. 

 

Limitations to Coverage under Limited Warranty 

This limited warranty does not apply to products that have been repaired or otherwise altered, except by 

Amantii or its authorized service representatives. This limited warranty does not apply to defects resulting from 

misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an 

incorrect power source. Products made by other manufacturers, sold with the product or thereafter, are not 

covered by this limited warranty. The use of unauthorized components will render this warranty null and void. 

 

Panorama Outdoor Units 

All Panorama units that are installed or in moisture intense conditions must use the stainless steel cover. Proof 

of purchase of the cover is required for any warranty claims 

 

Defects 

Defects must be brought to the attention of the selling dealer. Please have your proof of purchase, 

catalogue/model and serial numbers available when contacting dealer; any and all service under the limited 

warranty requires a proof of purchase of the product. Should a product or part covered by this limited warranty 

be proven to be defective, in material or workmanship, and during the two (2) year limited warranty period, 

Amantii will replace such defective product or part without charge. If Amantii is unable to replace such product, 

or if replacement is not commercially practicable or cannot be timely done, in its sole discretion Amantii may, in 

29

Summary of Contents for TRADITIONAL XTRASLIM Series































Reviews: