background image

4

Safety Precautions

Anyone operating the machine should read the 

following carefully and be informed of potentially 

dangerous operating conditions. Operators should 

be familiar with the location and use of all safety 

devices on the machine. DO NOT use the machine 

if it is not in proper operating condition, and report 

any damage or operation faults immediately.

DANGER!

  Failure to read the Owner’s Manual prior to 

operating or attempting any service or maintenance 

procedure to your machine could result in injury to 

you or to other personnel; damage to the machine or 

to other property could occur as well. You must have 

training in the operation of this machine before using it. 

If you or your operator(s) cannot read English, have this 

manual explained fully before attempting to operate this 

machine.

DANGER!

  This machine has parts, including the pad 

assemblies, that can cause severe injury if these parts 

are contacted while they are moving.  DO NOT allow 

any part of the body or clothing to come in contact 

with these parts while they are moving.  DO NOT try 

to change attachments while the machine is running.  

DO NOT allow other people to come near the machine 

while it is in operation.  DO NOT allow machine to run 

unattended.  DO NOT leave the machine in a place 

where unauthorized or untrained personnel could use 

the machine.  DO NOT run the machine with the pad 

off center, damaged, or missing.  DO NOT operate the 

machine if the machine has loose parts.

DANGER!

  Injury can occur to the eyes and body while 

using the machine.  Safety goggles, safety shoes, and 

safety clothing are recommended while operating the 

machine.

DANGER!

  Operating a machine that is not completely 

or fully assembled could result in injury or property 

damage. 

DO NOT

 operate this machine until it is 

completely assembled. Inspect the machine carefully 

before operation.

DANGER!

  Electrocution could occur if maintenance and 

repairs are performed on a unit that is not disconnected 

from the power source. Disconnect the power supply 

before attempting any maintenance or service. Always 

remove the electrical plug from the electrical outlet 

before changing the brush, pad or other attachment and 

before leaving the machine.

DANGER!

  Using a machine with a damaged power 

cord could result in an electrocution. 

DO NOT

 use the 

machine if the power cord is damaged. 

DO NOT

 use the 

electrical cord to move the machine.

WARNING! 

 

Machine vibration may cause tingling or 

numbness in the fingers and hands.  Gloves are 

recommended to reduce machine vibration.  If tingling 

or numbness persists, shut off the machine.  If vibration 

is caused by loose parts, adjust or tighten these parts 

before using the machine again.

WARNING!  

Modifications or alterations to this machine 

can lead to personal injury or damage to the machine. 

DO NOT

 make unauthorized modifications or alterations 

to this machine. Amano Pioneer Eclipse assumes 

no liabilities for injury or damage resulting from an 

unauthorized modification or alteration to the machine.  

Any unauthorized modification or alteration to this 

machine voids all warranties.

WARNING!

  Electrical components of this machine can 

“short-out” if exposed to water or moisture. Keep the 

electrical components of the machine dry. Wipe the 

machine down after each use. For storage, keep the 

machine in a dry building.

WARNING!

  Always use a three-wire electrical system 

connected to the electrical ground. For maximum 

protection against electric shock, use a circuit that is 

protected by a ground fault interrupter. Consult your 

electrical contractor.

WARNING!

  To prevent damage to the power cord, 

DO 

NOT

 let the pad, pad driver or wheels touch the power 

cord when the machine is running. Always lift the cord 

over the machine. 

DO NOT

 pull the power cord to move 

the machine.

WARNING!

  Operating a machine without observing all 

labels and instructional information could result in injury 

or damage. Read all machine labels before attempting 

to operate. Make sure all of the labels and instructional 

information are attached or fastened to the machine. 

Get replacement labels and decals from your authorized 

distributor.

WARNING!  

Machine vibration may cause tingling or 

numbness in the fingers and hands.  Gloves are 

recommended to reduce machine vibration.  If tingling 

or numbness persists, shut off the machine.  If vibration 

is caused by loose parts, adjust or tighten these parts 

before using the machine again.

WARNING!  

Use of this machine as a step or furniture 

could result in injury or damage. 

DO NOT

 use this 

machine as a step or furniture. 

DO NOT

 ride on this 

machine.

WARNING!

  To avoid injury keep hands, feet and loose clothing 

away from all moving parts of this machine.

WARNING!

  Any alterations or modifications of this 

machine could result in damage to the machine or 

injury to the operator or other bystanders. Alterations or 

modifications not authorized by the manufacturer voids 

any and all warranties and liabilities.

CAUTION!

  The machine is heavy. Get assistance before 

attempting to transport or move it.

Summary of Contents for Pioneer Eclipse 225BU



























Reviews: