Amana RHA**B2A Series Installation Instructions Manual Download Page 9

9

9

ROOM THERMOSTAT

(6 wires)

BHA BLOWER COIL

(5 wires)

RH OUTDOOR UNIT

THERMOSTAT* CONNECTIONS TO RH-HEAT PUMPS

WITH INDOOR BHA BLOWER COIL

COLOR CODE

1ST GROUP COLOR

2ND GROUP NUMBER

OR-ORANGE

BK-BLACK

YL-YELLOW

BU-BLUE

VT-VIOLET

RD-RED

BR-BROWN

TN-TAN

GN-GREEN

GY-GRAY

WARNING

To avoid personal injury, shock or death, disconnect the
electrical power before electrically connecting any
equipment or changing any existing wiring.

A) No Outdoor Thermostat - Electric Heat Supplied During Defrost

Notes: (1) BHA-TB blowers may require additional wire(s) here.  See BHA-TB wiring diagram for details.

(2) “Emergency Heat” will stop the compressor, but it will not bypass the outdoor thermostat.  Only the amount of

heat controlled by W2 will be energized above the ATK setpoint.

(3) See notes on page 12 regarding connector, GY42 wire, and staging of electric heat.

 

 

W2 

 

 

 

C/X 

RHxEH001

W1 

W2  E  G 

C/X 

O

R  Y 

W2  E    

C/X 

O

(1)

(1)

ROOM THERMOSTAT (2)

(6 wires)

BHA BLOWER COIL

(5 wires)

RH OUTDOOR UNIT

B) With Outdoor Thermostat - Electric Heat Supplied During Defrost

ATK Not Controlling 1st Group of Electric Heaters - 9.6 to 28.8 KW

 

 

W2 

             GY42   

C/X 

RHxEH002

R W1 Y W2    E    G C/X O

ATK05

(1)

(1)

(3)

R  Y 

W2  E    

C/X 

O

Notes: (1) BHA-TB blowers may require additional wire(s) here.  See BHA-TB wiring diagram for details.

Summary of Contents for RHA**B2A Series













Reviews: