7
Troubleshooting
LED/Switch Test
While in Service Mode, press the
Delay
key to start a LED/Switch check.
All the LEDs can be toggled or slewed by
pressing the key associated with the LED or set of
LEDs.
All keys (including the
OFF
button) must be pressed
within 5 minutes for this test to pass.
“PA”
will be
displayed for five (5) seconds once all keys have
been pressed and the test is completed. Following 20
seconds of inactivity at any point, this test will exit
without any display. The
Power Off
switch pad must
be pressed twice within 30 seconds to cancel this test.
Board Input Test
While in Service Mode, pressing the
Spin Only
key will begin the
Board Input
Test.
This test turns on a specified output
after a key press. Pressing the
Spin Only
key again cancels the test.(Display shows
in
).
While in Service Mode follow chart to check respective
function.
• When the “Rotary Cycle Selector” is set to “Super Wash” and
the “Rotary Cycle Selector” is pressed, the door position will be
displayed:
OP
if open,
CL
if closed.
• When the “Rotary Cycle Selector” is set to “
Normal
” and the
“Rotary Cycle Selector” is pressed, the Lock position will be
displayed:
UL
if unlocked,
LO
if locked.
- When the “Rotary Cycle Selector” is set to “
Quick Wash
” and
the the “Rotary Cycle Selector” is pressed, the High water level
will be displayed:
-0
if below level,
-1
if above level. The High
water level is defined as the over flow water level.
• When the “Rotary Cycle Selector” is set to “
Wrinkle
Control
” and the the “Rotary Cycle Selector” is
pressed, the Medium water level will be displayed:
-0
if below level,
-1
if above level. The Medium water
level is defined as the minimum water level needed
such that the heater can be turned on.
• When the “
Extra Rinse
” is pressed, the Low water
level will be displayed:
_0
if below level,
_1
if above
level. The Low water level is defined as the reset
water level.
• When the “Rotary Cycle Selector” is set to “
Hand
Wash
” and the the “Rotary Cycle Selector” is pressed,
the level of Tub unbalance will be displayed:
UC
if
balanced,
UO
if unbalanced.
U0
will be displayed
during the time when the machine is correcting for the
unbalance; e.g. slowing down to redistribute the load
or to get to a lower spin speed. Once the situation has
been corrected (i.e. the load has begun tumbling or the
lower speed has resulted in an acceptable amount of
unbalance);
UC
will once again be displayed.
• When the “
Delay
” switch pad is pressed, the water
temperature will be displayed: degrees F.
- When the “Rotary Cycle Selector” is set to “
Delicates
”
and the “Rotary Cycle Selector” is pressed, the water
temperature will be displayed: degrees C (Celsius).
Switch
Delay Start
Chime
Extra Rinse
Soil Level
Spin Speed
Temperature
Rinse&Spin
Spin Only
Selector Knob
Selector Knob
Start Pause
Selector Knob
Power Off
Action
Press once
Press 3 times
Press once
Press 4 times
Press 5 times
Press 5 times
Press once
Press once
Rotate 1 full revolution clockwise
1 position counterclockwise
Press once
Press once
Press once
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
Selection
Function
Display
Rotary cycle
selector set to
Super Wash.
Press Rotary
Selector Knob.
Door position
“
OP
” or “
CL
”
Rotary cycle
selector set to
Normal. Press
Rotary Selector
Knob.
Lock state
“
UL
” or “
LO
”
Rotary cycle
selector set to
Quick Wash.
Press Rotary
Selector Knob.
High water level
“
– 0
” if below level.
“
– 1
” if above level.
