background image

International Commercial Microwave—Technical Information

 

April 2006 

16025979 

©2006 Maytag Services 

240/230 VAC, 50 Hz Models 

RC5KFT2 P1331424M 

RC5MDTS2 

P1331427M 

RC5MDTM2 P1331428M 

RC520T2 

P1331423M 

  Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or 

repair of this unit. 

  Refer to Service Manual 16022149 for installation, operating, testing, troubleshooting, and disassembly instruction. 

CAUTION

!

 

All safety information must be followed as provided in Service Manual 16022149. 

!

WARNING

 

To avoid the risk of electrical shock, personal injury or death; disconnect power to oven and discharge capacitor 
before servicing, unless testing requires power. 

Models RC5KFT2 

RC520T2 

RC5MDTS2 

RC5MDTM2 

Power Source

 

 

 

 

 

Voltage AC 

230/240 VAC 

230/240 VAC 

230/240 VAC 

230/240 VAC 

Amperage (Single Unit) 

16 A 

16 A 

32 A 

32 A 

Frequency 

50 Hz 

50 Hz 

50 Hz 

50 Hz 

Single Phase, 3 wire 
grounded 

X X X X 

Plug 

CEE 7/7 Schucko 

CEE 7/7 Schucko 

IEC 309-32A 

Marechal DS3 

Power Output 

 Microwave

 

 

 

 

 

Nominal microwave energy 
(IEC705) 

1800 Watts 

2000 Watts 

2400 Watts 

2400 Watts 

Minimum temperature rise (

T) 

18ºF / 10ºC 

20ºF / 11ºC 

24ºF / 13ºC 

24ºF / 13ºC 

Operating Frequency 

2450 MHz 

2450 MHz 

2450 MHz 

2450 MHz 

Power Consumption

 

 

 

 

 

Microwave only 

2950 Watts / 12.8 A

3000 Watts / 13 A 

3900 Watts / 17 A 

3900 Watts / 17 A 

Dimensions 

 

 

 

 

Cabinet (cm in) 

 

 

 

 

Width 

49 cm 

19 1/4" 

49 cm 

19 1/4" 

49 cm 

19 1/4" 

49 cm 

19 1/4" 

Height 

46 cm 

18 1/4" 

46 cm 

18 1/4" 

46 cm 

18 1/4" 

46 cm 

18 1/4" 

Depth 

67 cm 

26 1/4" 

67 cm 

26 1/4" 

67 cm 

26 1/4" 

67 cm 

26 1/4" 

Oven Interior (cm in)

 

 

 

 

 

Width 

33 cm 

13" 

33 cm 

13" 

33 cm 

13" 

33 cm 

13" 

Height 

22 cm 

8 1/2" 

22 cm 

8 1/2" 

22 cm 

8 1/2" 

22 cm 

8 1/2" 

Depth 

38 cm 

15" 

38 cm 

15" 

38 cm 

15" 

38 cm 

15" 

Weight (kg lbs)

 

 

 

 

 

Uncrated 

52 kg 

115 lbs.  52 kg 

115 lbs.  52 kg 

115 lbs.  52 kg 

115 lbs. 

Crated 

56 kg 

123 lbs.  56 kg 

123 lbs.  56 kg 

123 lbs.  56 kg 

123 lbs. 

 

Summary of Contents for Menumaster P1331423M














Reviews: