5
5
5
5
5
5
5.
Using a cordless drill, drill a
¹⁄₄
" hole in the cold water pipe
you have selected.
6.
Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the
¹⁄₄
" drilled hole
in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
slowly and evenly so the washer makes a watertight seal.
Do not overtighten.
7.
Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten, or
you may crush the copper tubing.
8.
Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.
Turn OFF the shutoff valve on the water pipe.
Connect to Refrigerator
1.
Remove plastic cap from water valve inlet port. Attach the
copper tube to the valve inlet using a compression nut and
sleeve as shown. Tighten the compression nut. Do not
overtighten. Confirm copper tubing is secure by pulling on
copper tubing.
2.
Create a service loop with the copper tubing. Avoid kinks
when coiling the copper tubing. Secure copper tubing to
refrigerator cabinet with a “P” clamp.
3.
Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Complete the Installation
1.
Plug into a grounded 3 prong outlet.
NOTE:
Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill the ice container.
Refrigerator Doors and Drawer
All graphics referenced in the following instructions are included
later in this section after “Final Steps.”
TOOLS NEEDED:
⁵⁄₁₆
",
³⁄₈
",
¹⁄₄
" hex-head socket wrench,
#2 Phillips screwdriver, and a flat-blade screwdriver.
IMPORTANT:
■
Your refrigerator may have a standard reversible refrigerator
door with either a freezer door or freezer drawer, or French
doors. Follow the instructions specific to the door style of your
model.
■
All graphics referenced in the following instructions are
included later in this section after “Final Steps.” The graphics
shown for the standard door are for a right-hand swing
refrigerator (hinges factory installed on the right).
■
If you only want to remove and replace the doors, see
“Remove Door(s) and Hinges” and “Replace Door(s) and
Hinges.”
■
Before you begin, turn the refrigerator control OFF, and
remove food and adjustable door or utility bins from the doors.
Remove and Replace Handles
Style 1 Handles
■
Using a 3/32" or 1/8" hex key, loosen the two setscrews
located on the side of each handle. Pull the handle straight out
from the door. Make sure you keep the screws for reattaching
the handles. See Style 1 Handle, graphic 1.
■
To replace the handles, reverse the directions.
Style 2 Handles
To Remove Handles:
1.
Grasp the lower part of the handle firmly, slide the handle up
and pull the handle straight out from the door. See Handle
graphic.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
A. Copper tubing
B. “P” clamp
C. Compression nut
D. Compression sleeve
F
G
A
B
C
D
E
B
A
C
D
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
