- 2 -
Trove AMAG M4000 Kits
Overview:
Altronix Trove AMAG kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/
chargers and sub-assemblies. Kits accommodate up to three (3) AMAG M4000 modules for up to twelve (12) doors in a single enclosure.
Configuration Chart:
Altronix
Model
Number
Power Supply Board Input Fuse Rating
Power Supply Board Battery Fuse Rating
120VAC 60Hz Input Current (A)
Maximum Supply
Current for Main and
Aux. Outputs on
Power Supply board
and ACM4/ACM8
Access Power
Controllers’ outputs
Nominal DC
Output Voltage
Fail-Safe/Fail-Secure or Dry Form “C” Outputs
Additional Fused Outputs
ACM4 Board Input Fuse Rating
ACM4 Board Output Fuse Rating
ACM8 Board Input Fuse Rating
ACM8 Board Output Fuse Rating
PDS8 Board Input Fuse Rating
PDS8 Board Output Fuse Rating
PD4UL Board Output Fuse Rating
[DC]
[Aux]
Output
Range
(VDC)
Output
Range
(VDC)
T2AGK3F8
5A/250V
15A/
32V
3.5
24VDC @ 5.4A
20.17-
26.4
20.28-
26.4
8
8
–
–
10A/
250V
2.5A/
250V
10A/
32V
3A/
32V
–
T2AGK7F12
6.3A/250V
15A/
32V
4.5
24VDC @ 9.4A
20.17-
26.4
20.28-
26.4
12
8
10A/
250V
3A/
32V
10A/
250V
2.5A/
250V
10A/
32V
3A/
32V
–
T2AGK75F12
eFlow104NB
6.3A/ 250V
15A/
32V
7.5
24VDC @ 9.4A
20.17-
26.4
20.28-
26.4
12
4
10A/
250V
3A/
32V
10A/
250V
2.5A/
250V
–
–
3.5A/
250V
eFlow102NB
5A/ 250V
12VDC @ 10A
9.7-
13.2
10.03-
13.2
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in
the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure. Mark the
position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper
keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired
location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure
approximately 2” from the right side (Fig. 1, pg. 2).
Connect tamper switch wiring to the Access Control Panel input or the appropriate
UL Listed reporting device. To activate alarm signal open the door of the enclosure.
4. Mount AMAG M4000 modules to TAG2 backplane, refer to page 3-5.
5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB, eFlow102NB,
eFlow104NB, and corresponding Sub-Assembly Installation Guides for the following
models: ACM8, ACM4, PD4UL, PDS8 and VR6 for further installation instructions.
Hardware:
Fig. 1
Tamper Switch
(provided)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure
Nylon Standoff | 5/16” Pan Head Screw | Lock Nut
