- 2 -
Trove CDVI Kits Installation Guide
Overview:
Altronix Trove CDVI kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/chargers and
sub-assemblies. These kits also accommodate various combinations of CDVI Atrium A22K/A22NB/ADH10 boards for up to twenty (20) doors
in a single enclosure.
Configuration Chart:
Altronix
Model Number
Networkable
Power Supply Board Input Fuse Rating
Power Supply Board Battery Fuse Rating
120VAC 60Hz Input Current (A)
Maximum Supply
Current for Main and
Aux. Outputs on
Power Supply board,
MOM5 power
distribution module
or ACM4/ACM8 Access
Power Controllers’
outputs
Nominal DC
Output Voltage
Fail-Safe/Fail-Secure or Dry Form “C” Outputs
Additional Fuse or PTC Protected Outputs
ACM4/ACM8 Board Input Fuse Rating
ACM4 Board Output Fuse Rating
ACM8 Board Output Fuse Rating
PD8UL Board Output Fuse Rating
MOM5 Output PTC Rating
Power Supply
[DC]
[Aux]
Output
Range
(VDC)
Output
Range
(VDC)
T1CVK3F4
–
5A/250V
15A/
32V
3.5
24VDC @ 5.7A
20.17-
26.4
20.28-
26.4
4
–
10A/
250V
3A/
32V
–
–
–
T2CVK7F10
–
6.3A/250V 15A/
32V
4.5
24VDC @ 9.4A
20.17-
26.4
20.28-
26.4
12
8
10A/
250V
2.5A/
250V
2.5A/
250V
3.5A/
250V
–
T2CVK33F10
–
5A/250V
15A/
32V
7.0
24VDC @ 5.9A
+
24VDC @ 5.9A
20.17-
26.4
20.28-
26.4
–
10
–
–
–
–
2A/
250V
T2CVK33F10Q
P
5A/250V
15A/
32V
7.0
24VDC @ 5.9A
+
24VDC @ 5.9A
20.17-
26.4
20.28-
26.4
–
10
–
–
–
–
2A/
250V
T3CVK77F20
–
6.3A/ 250V 15A/
32V
9.0
24VDC @ 9.4A
+
24VDC @ 9.7A
20.17-
26.4
20.28-
26.4
20
8
10A/
250V
3A/
32V
2.5A/
250V
3.5A/
250V
–
9.7-
13.2
10.03-
13.2
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
If your application requires a raised backplane, re-mount it using metal spacers and screws (provided).
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install two/three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two/three upper screws; level and secure.
Mark the position of the lower two/three holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the
enclosure’s upper keyholes over the upper screws. Install the lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch(es) (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the
tamper switch bracket onto the edge of the enclosure approximately 2” from the right side
(Fig. 1, pg. 2)
. Connect tamper switch wiring
to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.
4. Mount CDVI A22K/A22NB/ADH10 boards to backplane,
refer to pages 3-6.
5. Refer to the
eFlow Power Supply/Charger Installation Guide
(eFlow6NB, eFlow102NB,
eFlow104NB) and corresponding
Sub-Assembly Installation Guide
(LINQ2, ACM4, ACM8,
PD8UL, MOM5) for further installation instructions.
Fig. 1
Tamper Switch
(provided)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure
